Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi everyone,I have an ISR 4431 with CME 14.1 installed and 2 IP Phones (Cisco 7821). The phones are getting an IP from the DHCP server but aren't registering.I've attached the configuration file, a debug file and pictures of the phones.I've tried fac...
I have a client who has multiple Cisco Codec Plus systems. The Presenter track camera is sharing without being prompted, causing the system to continuously display the camera image of presenter track on the monitors in room even when empty. If you pu...
Cisco Jabber (IOS_14.3.0.308356) for iPhone/iPad: vibration option missing after IOS version upgrade to 17.2 on iPad.Vibrate option was available and tested as below:Jabber setting-->Sounds-->Receive calls option ON means ringtone is enabled. Jabber ...
Hi, I was wondering if there is an MPP (multiplatform) version of the 8875 phone. For example 8865 comes with the code 3PW or 3PCC. If it does, does someone knows the part number?Thank you!
Hi, Right now i faced issue on my pabx system, so when people wanna try to call to our PSTN number (SIP TRUNK NUMBER) from othe PSTN number its perfectly fine, but when people try it from GSM number or cellular number the call cannot be done, the err...
Hello,Trying to connect a 8800 KEM to a 8865 phone. Have looked at several forums and threads, tried all the settings. Still get the same message on the phone when I connect the 8800 'the phone is not set up for the expansion module'. In CUCM have ...
Hello, I want to test SIP trunk on my Cisco CME. I make call from local phone to out, but i can not make call from outside to my local. i run debug, and i found . %CALL_CONTROL-6-CALL_LOOP: The incoming call has a global identifier already present ...
Hi,I am trying to understand the call flow for transcoding SIP calls.here is the setup CUCM---CUBE---SIP Gateway CUBE has local transcoding interface (LTI) setupto transcode the following codecsg711ulawg711alawg729ar8g729abr8g729r8 An incoming call f...
I've followed this https://community.cisco.com/t5/ip-telephony-and-phones/configuring-vic2-2fxs-and-vic2-2fxo-to-make-call-thru-them/td-p/2207237 to get my fxs ports talking to each other, config below. How do i route calls coming in from voip, or a ...
Good morning, Unify third party SIP phone Openstage 15 SIP registered on CUCM 12.5 doesn't subscribe. CUCM reject the request with code 403 Forbidden and the message "Dialog package not licensed". Is there a way to make the CUCM accept the subscripti...
I have forgotten CMS's admin password, and I can't find any way to recover it.please any help, there is no reference through the internet or cisco about this problem.
I'm trying to setup a home lab. I have a Cisco switch and router and CUCM 10.5 running on vmware. I have two IP phones a 7962 and a 7942 that will get IP addresses, but wont register with CUCM. I can't ping the phones from CUCM. I can ping them from ...
Bit of a strange question, but I noticed that when I take a look at my Cisco SIP phone logs (pulled from the phone), the Invite request doesn't contain the dialed number. Example: INVITE sip:***@10.20.160.3;user=phone SIP/2.0^MVia: SIP/2.0/TCP 10.20....
Hi,i want to bulk edit UDP BLF Buttons for 50+ Users.I export all UDP with all details, modify the BLF fields in that csv and uplodd it for UDP - Insert All Details.But i get Errors for every BLF button:Error : Missing key in referenced table for ref...
Hello , I have ATA191 that line 1 is registered but line 2 is not registered. line 1 mac (example BBAAAAAAAAAA line 2 mac (example): AAAAAAAAAA01 my CUCM version is 11.5 any idea?
