IP Telephony and Phones

International Call report in CM

Is there a way to run an International call report in Call Manager? To find out which International calls have been made and by whom. Any info would be great.

CDR when using H323 GW

We have a H323 gateway with different bearers on each interface. Our CILE cannot establish which interface was used for a call so we are unable to apply correct tariff. Is it possible to distinguish interface used?

B channel problem between Cisco 3745 and Avaya PBX

We have two PRI connections between router and pbx running wth isdn switch-type primary qsig, outbound calls from the pbx work fine and all b channels work okay. For inbound calls we have the following situation PRI 1/0 - Channels 17 - 31 not working...

vg regesiter, ip add

my voice gateway has many IP address, when my mgcp gateway registers on CCM, which ip address it uses for register? the higher ip add ? can I use a loopback ip add ?

Strange CCM behaviour after installation

Hi GuysI am having a very strange problem that I am hoping someone can help me with:I have installed CCM 4.1(3) on a laptop. I have performed a non-mcs installation hundreds of times before without any issues. During this installation, there were no ...

remotely verifying fxo line

Anyone know of a way to verify whether an fxo port on a remote device has a live line connected to it or not? We have routers in remote locations that we believe the CO loop lines are not functioning or connected to the wrong ports. Wanting to know...

7936 rebooting

Hi,I have couple of 7936's that keep rebooting in one of our offices.I know they both work because of i move them to another office they work fine.I have adjusted speed/duplex , removed the voice vlan and also updated to the latest code 3.3.12.Any id...

call problem with MGCP

I,ve got an 2821 gw with dsp an fxo ports, when the router recieves a call on the fxo port the call is forwarded to the ip telephone and fails, busy tone is heard form the telephone that is calling.The CSS, partitions and the mgcp is configured right...

Forcing CCM to use g729r8 instead of g729br8

I have a CCM setup, and have the strip g729 silence suppression/VAD Annex B capability from codec set to TRUE under CCM service parameters, but calls across WAN are showing up as g729br8 that come in from PRI on MGCP gateway. There is a 6608 being us...

Phone registration issue

I?m having problems with a CCM 4.1(3) cluster that consists of one publisher and one subscriber. If a new phone registers to the publisher, no one can call the phones extension, even though everything is setup correctly. What would cause this?Thanks,...

7920 stuck on connecting to callmanger 0

I am using a 2811 router with CCME on it and have a hwic ap. I am trying to get a 7920 to work. All the display says is connecting to callmanager 0. The phone picks up a dhcp address,tftp address and can ping the phone address. I have attached config...

Resolved! Transfer recall on ccm 4.1(3)

i need some help in setting up transfer recall on the ccm 4.1...as in when we transfer a call to somebody and it's not answered after a 3-4 rings, it should be transferred back to the person who transferred it.

==CME 4.1.3 Unable to use Outlook Dialer/TSP==

Hello folks!I try to use it but it doesnt work, in fact I do the follow steps and neither work:For Windows 2000/XP: From Control Panel execute the "Add/Remove Hardware" utility. Select "Add/Troubleshoot" when the prompt "Choose a Hardware Task" is di...

7936 Conference Phone

Has anyone run into an issue getting a 7936 conference phone to register to call manager?CM version = 4.1 3 sr2

CM or CME ?

Hello,I'm new with Cisco.We are completly rebuilding our sites and we look to use VOIP.We have 3 sites :- 1 in Belgium : approx 50 users- 2 in Frans : 5 users. (and all call from Belgium to anywhere in Frans transit via one of them)Between these site...

IP Telephony and Phones

Forum Posts

International Call report in CM

CDR when using H323 GW

B channel problem between Cisco 3745 and Avaya PBX

vg regesiter, ip add

Strange CCM behaviour after installation

remotely verifying fxo line

7936 rebooting

call problem with MGCP

Forcing CCM to use g729r8 instead of g729br8

Phone registration issue

7920 stuck on connecting to callmanger 0

Resolved! Transfer recall on ccm 4.1(3)

==CME 4.1.3 Unable to use Outlook Dialer/TSP==

7936 Conference Phone

CM or CME ?

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

CUCM sends wrong device ID to Recording System

CDR reports: Request for activity on multiple lines

I get dozens of these alarms on WU, but no errros on controller

Transfer Caller ID and 8800 Line Buttons CME

UCCX upgrading Error encountered: The selected file is not valid.

7861 BLF Phone not showing green idle status.

Voice call flow working just one direction in VOIP CUCM to POTS CME

Cisco 8865 use all feature/session keys as Speed Dial

Common Phone Profile 8841

Cisco MTP resets needed sometimes 2x per week? Is this necessary?