Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
this may seem a silly question, however i'm still going to ask.i have configured CME (3.3) and have an E1 PRI voice circuit to the PSTN however my voice vlan (3) is fine, however data access (i.e. services and browser acccess) would be gained throug...
Running CME 4.0.3 with about 40 sccp 7940/60 phones. I would like comments on which firmware 7.x or 8.x is best to run on the phones in a cme environment. Also, Anyone out there running 8.x on CME 4.0.3 system??Thanks in advance,Tony
Hi,I have kind of a newbie question and am sorry for posting such queries but I can't find an explanation anywhere on the net. I am wondering what you understand under the term "toll bypass" and how you associate it with VoIP. I am currently studying...
Hey everyone:My customer doens't want to by the IPCC to have a call center capability. Actually his call center is only 9 agents so i guess we can do something using the call manager and/or UnityHis version is CCM 4.0 and Unity 4.0(5) can we do somet...
What is the report you can run in CCM to show you echo from the IP phones?
I need to connect CCM to h323 service provider. I have 2811 (c2800nm-ipvoice-mz.124-13a.bin) which is connected to h323 provider. I need to know what configuration i must do on 2811 and what to do on CCM. Thx in advance.
Hello everyone,I have another strange issue with an IP phone that doesn't want to ring.There are 4 analog lines plugged into an FXO card in the router, and all are configured the same. The lines are PLARed to the phones - and all but one are working....
HiOne of the admin guy setup password on MCS7825 Server. Is there way to bypass it as each time we cold start the server it asks for password.Thanks in advance.Shahid
Hello everybody,HELP ANYBODY.I work on a implementation that from PSTN any number can call to GDN 24133450, and then forward to another number on the PSTN.This is a E1 fractional ISDN PRI with 6 GDN and each GDN has 5 trunks. In order for the call go...
Hi,Cisco7941G with CCM5.0(4a), we tried to use the Plantronics 26716-01 cable which it says it does not require any amplifier and can be directly connected to the phone as per following:http://www.headsetsdirect.com/accessories/26716-01.htmlBut the h...
Hi to all,I have a an ata 186 (registered with a CCME version 4.0) to which an analog phone is connected.When an external call arrives to my ataa can hold the call and dial an internal ip phone but if the internal phone doest'n pick up and i resume ...
Dear Friends, i have only one CCM in my network, if it fails due to some problem, what happened to active calls, will all the active calls will be disconnected , can i make new calls while CCM is down. Pls note it, i have only one CCM. My next questi...
I have a production unity, vm only, that I will be migrating to a new server platform. On the new server, I have Unity installed up to the point of the telephony integration. On the DiRT procedure, I see that Unity must be completely installed befo...
Hi All,I have a CCM 4.1 configured at 2 differents site Cluster1 & Cluster2 linked by a trunk.Calls are flowing successfully over the trunk.I have configure the directory and can access them on each cluster.My problem is that i cannot access director...
Hi,I am having problems with an FXO card in the UK (BT is the telco). Could anyone please post a working Voice-port config for a single analogue BT line connected to an FXO port?I have tried numerous settings and can't get it to work. When I make an ...
