Greetings to all. Currently my problem is this. 3 Locations, Location A is a CallManager 4.0, Location B is an Avaya G3si and Location C is another Avaya G3si with an Intuity Audix connected via CLAN integration. When a user at Location A calls ...
Hello,We had 3 dropped calls when making and receiving calls over an ISDN30 Circuit.I searched in the Q931 Translator and dicovered one of the calls. I have attached the Q931 TRanslation output which may indicate (to the trained eye) why the call dr...
I have a new 3825 running c3825-ipvoicek9-mz.124-4.XC4.bin as recommended by cisco for using 7931 phones, I have a VWIC2-1MFT-G703 card installed, "1 Channelized (E1 or T1)/PRI port" shows up in the "show ver" command, however there is no controller ...
Hi,I need to make a program to place call, open pop-up on incomming call.I have the TApi developer Guide for CCM 4.2. But, I don't know wich language is better (C++, VB, ...) and how to use.The example in PDF is not clear for me. I'm not able to find...
hi:My case that i have multilocation and in each site i have a voice gateway and the users have permition to call an outgoing call such as mobile 07XXXXXXX, my point that how can configure this common pattern to be route for each location gatewaytha...
In our system we have some 7960 IP phones and I have been asked to setup 6 different lines on one of them. Normally this would not be an issue at all as I could just go to the phone and add a line. After adding 4 lines I have found that I cannot ad...
Can someone please set me straight. From what I can gather in this documenthttp://www.cisco.com/cgi-bin/Software/Tablebuild/doftp.pl?ftpfile=cisco/crypto/3DES/voice/callmgr/4.1/ciscocm.4-1-3-2007-DST-Update.1-0-1-readme.htm&app=Tablebuild&status=sho...
Has anyone modified the callmanager Global Directory in such a manner as to allow more fields to be searched upon in the Directory search on the phones? Management would like to have more fields to search on but I believe in order to have this abilit...
I'd like to intercept packets from my Cisco IP Phone 7912 series to my PC (plugged into the phone's PC port). What do I have to do in order to capture the phone's output at a packet level?Thanks. -Scott
Hello, I'm new with IP Telephony and I would like to ask something on the matter. I have a voice gateway and I have some faxes. The gateway is configured with MGCP and the IP telephony network is working succesfully. I have a problem with faxes, some...
I just setup a non-gateway intercluster trunk between my company and a client of ours. I then setup a translation pattern for the called number 9000 to route to my extension. The client setup a route pattern to send any calls to 9000 over the trunk...
I need help on the CCM 5.0 configuration, that how i can send call from my SIP phone to SCCP phone.Also help me out that how i can configure the SIP Route Pattern and SIP route inside the CCM 5.0regardsMuhammad Rehan
i am not sure how the exmergedata folder got created in the c: drive. we have unity back up scheduled everyday. the exmergedata folder contains all the .pst files which consumes hell lot of space on the c: drive to the extent when unity stops storing...
I have dual FXS port card installed on 2800. One of the port stays busy. I can clear it without reload the router. This happened once before. I'd like to what will be the problem. Any ideas? Thanks.
Guys, Somebody would know to say me if is possible to associate one callerID for incoming calls (not to associate one callerID to port fxo)? If affirmative, as the configuration must be madeRegards,Wilson
