Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear All,I am running virtual CME (12.6) and Virtual CUE (10.5) in a lab environment (both using evaluation license). I tried both SCCP and SIP CME configuration. I could not create web admin user and the telephony-service or voice register pool. Als...
I have just recently changed our General Dynamics Sectera vIPer devices from Firmware 4.2.1 to 5.2.1. I am running CUCM 11.5.1. According to General Dynamics Support staff, when I make the change from 4.2.1 to 5.2.1 with our CUCM version, I have to...
Active Load ID:sip8831.10-3-1SR3-4Download Status:FailedRequested Load ID:sip8831.10-3-1SR2-2Download Server:XXX.XXX.XXX.XXXInactive Load Failure ReasonInternal Phone Error Above is the phone status in CUCM (release 11.5.1). We have 7841 and 8861 s...
Hello everyone,I wonder if it possible to configure the cap for outgoing calls (outgoing call blocked after reaching specific number of external calls e.g. 100).CUCM System version: 11.5.1.13901-3Thank you for any advice or recommendation. Regards,Da...
This is a VG350 that is MGCP registered to a CUCM 11.0 I understand what is going on, but not how to fix it. Essentially we have these emergency call boxes. Someone hits the button and the call box goes off-hook and hits a blank translation patter...
Hi guys I have a question that regarding cuwl std license , I found document from cisco that describer CUWL Standard : supports advanced (voice and video) call control features including desktop and mobile with maximum of two devices per user. but i...
We have 7942 Phones and 7841.Coustmer requirement: Three manager assicate with one asstant.I tried to configure on 7942 phones but assistant end user drop list assitant configuration : unable to assign more than one manager.assitant Phone line 1 : as...
Good day Sir/Madam How can I change Voice mail of CISCO IP Phones We currently have:CISCO UNIFIED CM CONSOLEVOICE SERVER Regards CHUMA MABINDLA
Hello Folks, We want to collect CDRs of SIP calls from CUBE. Is there anyway to do this ? Also for capacity planning, we have been unsuccessful to receive trunk utilization report from ITSP so we would like to explore if there is any way to capture ...
I am using Cisco unified call manager 11.5 and I have a instance where one phone number is repeatedly trying to call another phone number in rapid succession. One of the numbers is a CTI group and the number being called is one that used to exist but...
Hello All, We have a requirement to capture the call logs that are coming via SIP trunk on CUBE's. We have TACACS server in our environment. May I know which is the best way to implement this to collect the CDR logs and will we have all the SIP relat...
Hi, I find that when the 8832 looses PoE, the CP-8832-MIC-WLS mics must be paired again. does anyone know if this can be avoided so that the mics do not need to be re-paired when PoE bounces?
Hello everyone >>>I have switch 2960x , I enabled .1x on interfacesNOW ... I want to add VoIP devices on switch but .1x not allow voip devices to get IPHow I solve it with stay .1x on interfaces
Hi GuysI am facing a problem, A customer would like to build a CUCM cluster for 500 jabber phone and 20 third-party brand SIP phone to replaced their existing PABX, for license that I found document from cisco that the CULW standard and pro support ...
Goodmorning everyone,I explain to you my problem that I am having with the call transfer on a Call Mnager Express:The moment someone receives a call, whether I receive it from the outside or from the inside, when I try to transfer the call to another...
