Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Experts,I am trying to delete the certificates from CUCM Publishers which has totally 5 nodes , out of 5 nodes 2 nodes are not in production and we have planned to remove it from network.But , that nodes have expiry date as year of 2022 and onc...
Hi,I can't make nor receive calls on a BRI interface, issuing a debug isdn q931 show the following ====OUTGOING====isdn test call interface bri 0/2/1:0 0677889922VG_router#*May 27 15:42:23.808: ISDN BR0/2/1:0 Q931: Sending SETUP callref = 0x0006 call...
Hi, I have two AVAYA 9608G registered with CUCM. But issue is that both are unable to call each other. Even I am unable to make a call from cisco phone to avaya phone. need help to solve the issue. I have to enable AUTO qos for AVAYA phone on cis...
Greetings. I would like to know if there is any way to see on the CUCM if a 8851 phone has a expansion module connected to it. As far as I know we load the configurations of the 8851 Phones ready to use the expansion modules, but unless we get direct...
I have a client that needs a phone in their large freezer room. I cannot find any phone that will work under 32°.We'd prefer VOIP but also fine with using an ATA if we need to. Any suggestions?
please advice if possiblethis apply to call center, let say have 10 IP phonescreate hunt pilot 1999 and associated with this 10 phoneeveryone is calling 1999 to reach out...how can from this 10 phone, when outbound call , it show 1999 not each indivi...
Hi,If I have a two pstn gateway ,What is the best way of creating route group ?Adding both pstn gateway into a route group or create different route group for each gateway .In my case I have a two pstn gateway and tsip trunk .Requirement is if sip fa...
Hello,I would like to setup a Bluetooth headset so that the pickup button and volume buttons can pickup calls and adjust volume when connected to a Windows 10 machine using jabber.This headset can work successfully with Cisco IP Phones 8851.The sound...
Hello, From our SIP trunk we are stripping down to just the last 5 digits of each incoming call. If the last 5 digits of the DID being called doesn't need to translate to a different extension we don't have any translation configured. One situation w...
I am using a 3945 router and I was able to make conference calls and snr calls with no problems at all. Then... We lost power and it caused the router to shutdown. When the power came back on, the router booted up and all seemed well.But, when I ch...
How can I configure calls from UserA extension and UserB extension to ring a few times on their own phones and if they're not able to answer, forward to UserC, but if UserC cannot answer return to the original extension voicemail? Example: UserA -> ...
Dear Experts,I have a setup with a CME (Version 12.1) on Cisco 4331 Router. The SIP trunk is terminated directly on the router. All IP phones are registered with CME using SIP. We have 7942, 8841, and 8845 IP Phones. 1) We had an issue in dialing any...
Hello,I have got a question about forwarding from many clients to one secretary.In our old Phone system we have membergroups and the coworkers forwarding every call to one secretary. People who were member in the group didn’t forward their call, so t...
Hi all, I was able to install the language pack for cuc i can see it in show version as active.I would like to know how can i apply the correct language pack for all the users instead of one by one. Can i use i user template - voicemailtemplate and c...
hi everybody,i have a problem with dtmf and cisco 2811 as voice-gateway, SIP-Trunk-Telco >> 2811 >> CUCM >> CUC(IVR) when i call our number which is 54878787, call goes through 2811 to IVR and i hear IVR-Voice-Message,but i can not input any number, ...
