Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am attempting to configure a 2951 with a Cube license to go between an IP phone system (Avaya IPO) and the SIP provider. When I call in, I see call info coming into the CUBE, however it never goes beyond there. When I attempt to make an outbound ...
So I work for a school district and am decent at working my way through our cisco phone system. But I have a specific type of search i would like to do if possible. I am looking to see if there is a way to search for external phone number masks. I h...
I configured Cisco phone “No Answer Ring Duration (seconds)” - 50 sec and then call should go to voice mail.It works for internal or incoming external(analog) calls.Inbound external calls through sip trunk drops after about 30 sec. if no answer Sip...
on every call call I am seeing this error. can not find any reference to it. Jun 16 23:46:50.452: %VOICE_HA-3-DATA_COLLECT_ERR: (ACTV-Call Leg Data Collect): HA Module SIPSPI reported DATA COLLECT failure (mainst ID:1093, CID:1093).Jun 16 23:46:50...
I have 3x Cisco 8831 conference phones which have worked on our CME for around 2 years now. But last week I noticed all 3 are showing "phone not registered". Checking debugs I see: 9078392: Feb 4 16:23:47.541: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplay...
Hey experts, I have been using TCL script since 4-5 years now. The script is its-CISCO.2.0.1.0.tcl which used to work fine on the 2900 series router. I used this script on 4000 series router and the script is not working as it used to work on the 2...
i have a cme and im planning to shift to cucm , i have attached part of the cme config , do i simply just remove the sip trunk dial peer on cme and create a sip trunk on the cucm instead? does the other side of the sip trunk need to change any config...
I am trying to setup a SIP trunk for testing/practice with sip-ua.com. However, I'm unable to register with tthe SIP server. See attached router config and debug ccsip output. This doesn't seem to be a dns resolution issue. Any assistance on further ...
I have a problem, after configure the tcl script I have noticed that take to long time to passes second Áudio prompt . How can I configure it to take less time?
We are building an app that get the audio stream (live stream and recorded) from voip call and pass it to a speech to text engine. The speech to text engine accept websocket as input. Is there any way that we can get the realtime audio/recorded audio...
ello Guys, I´m having issues when performing hold or transfers via sip provider. The scenario is like this: PHONEA-CUCM-CUBE-SIP PROVIDER When PHONEA receive a call,from outside (sip provider), if the user puts the call on hold/transfer, the user ...
Dears,We have a CUE SM running on 2921 Router. We forgot both CLI and GUI password for this. How we can reset it? Best RegardsAbdul
We have a new setup , where we have :- 1. Informacast Paging Server in Vlan 14 of Core Switch-3850 ( Paging Server IP : 10.10.14.5) ------ Server Vlan SVI IP Address - 10.10.14.1 (Core Switch 3850 ) 2. IP Phones in Vlan 11 of Access Switch...
I have purchased a Cisco 7962 telephone. It is set up with SIP firmware, the os load is onu42.9-0-3TH1-22.sbn.I have a tftp server running on my network and I just want to configure this phone to either connect to my yeastar ip pbx system or directly...
Hi,I have this puzzling issue that for the life of me I cannot figure out. I searched high and low to no avail and wondering if there is anyone out there that knows how to do this. How do I go about creating voicemail mailbox accounts for hunt groups...
