Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, Here's my scenario; I have 3 buildings that are within a couple miles of each other. Each building has CUCM & SME 11.5 subscribers, the main building where the AT&T sip/bvoip circuits terminate to has the publisher a sub, CUBE & SME. I have MP...
We are a small school system and I was wondering if their is a requirement for School systems by law to have emergency responder configured on their network. What is the pro's and con's from having ER configured on the network versus having SRST co...
Hello, looking for a document that spells out the minimum version needed for ESXi to host CUCM 11.5 All replies rated. Thanks in advance!
Iwant to autoprovisioning a cisco 8865 with broadsoft but need the 3pcc firmware when will it be available the firmware to upgrade? Regards Thanks
Hi, i have a cp-8851 with firmware sip-88xx.10-3-1-20, and i want to upgrade to Multiplatform Firmware sip88xx.11-2-1MPP-630.loads When phone tries to upgrade, fails with: Inactive load: sip88xx.11-2-1MPP-630 I want to use this phone with Asteris...
Is there a way to get Cisco Jabber for Windows to work without a Presence Server and without a WebEx Server. Just with Cisco Unified Communication Manager 8.6 and Cisco Unity Connection, same Version?
Hi I have CuCM 8.6.2 and we run CiPC 8.6.6 I have a CiPC user who works fine when in the office however when they now try to use remote access via a VPN, which has worked normally for many years the phone doesnt register. I eventually tried a pac...
Hello everyone, I face the following issue in one of the offices. I wonder if you had experienced it before. The function at the phone, when using the “call forwarding” – button, doesn´t work. Setting the call forwarding directly in CUCM works, di...
We have configured Cisco 7841 IP Phones and 88XX series IP Phones. 1 We are able to make concall internal numbers IP Phones properly and call log list numbers. 2 Not able to make concall on external numbers by inputing manual numbers: When we try ...
Hello , I have router 2911 Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M3, RELEASE SOFTWARE (fc2) After an unexpected reboot it says: System returned to ROM by bus error at PC 0x357F0454 before reset the router ...
I need to have a phone ring three times when you call and if no answer then go to a broadcast group. Can I do This? There are 8 members on this group. The first time you call a member of this will need to have the same configuration. Thanks
Hi I have a few hundred c7945 phones registered. The majority show the load/active IDs as follows: Load ID - SCCP45.9-4-2SR1-1S Active Load ID - SCCP45.9-4-2SR1-1S I’ve noticed about 10 show the Active Load ID to be different: Load ID - SCCP45.9-...
I have CUCMBE 7.1 integrated to AD and have successfully sync CUCM users into LDAP from AD. However, Unity Connection doesn't see them to import if I go to TOOLS> IMPORT USERS> and Find End Users in UC. Is there anything else I need to do to import u...
Hi everyone, I'm running into an issue with outbound calls that is stumping me big time. Last week we had a couple of building power outages that outlasted our UPS so our network devices powered off and on ungracefully. This event fried our two 3845 ...
Anyone ever register a VIP-156PE ATA from Planet to cisco communications manager? I'm wondering what settings may work for planet's cryptic sip settings screen,
