Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Due to Cisco bug CSCux82917,- loose routing(lr) needs to be disabled or removed from record-route header. SCRIPT1 and SCRIPT2 is not working can someone please assist. The header I'm targeting is Record-Route: <sip:hu-gen-sip-pxy-pool.xxx.com:5060;l...
Hi all, I'm working on a new SRST configuration with E1 to the provider and SIP towads CUCM with +E164 DN. Here in the past we used COR list to avoid wrong dial-peer matching. Now, with the new dial-peer group feature this might be more elegant but...
Folks, When a person forwards a phone call to his cell phone using single number reach, is it possible to display the actual number of the person who is calling. The actual caller id should display on the cell phone. Any settings can be do t...
We had a CME - CUE integration that was working well. All pieces appear to be online. I need assistance with when we dial the automated attendant as well as the voicemail pilot number, we get dead air, then a ring and then a busy. We are getting som...
Hi, we have one cube and sip to service provider(SP) , management is considering another redundant SIP trunk to be established via another l3mpls network we use for data traffic only . The thing is CUBE is not directly connected to that l3mpls networ...
Dear all. We want to enable Cisco Any Connect VPN client on our Cisco 8865. To do this we follow the following process:https://www.cisco.com/c/en/us/support/docs/unified-communications/unified-communications-manager-callmanager/115785-anyconnect-vpn-...
Hi, I am updating UCM to 10.5.2.1to 10.5.2.169 , but OS admin shows updating for 8 hours & still spinning.There is no logs added during last 6 hours. Please check the attached logs & advise. Thanks Suchi
Hello , I have problem with outgoing calls external with PRI on router 4321 with version Version 15.5(3)S4b. the problem occures when we dialing outside via PRI I receive busy , on debugging we see error message " Resource unavailable, unspecified". ...
I have this on any of our 7962's with two direct lines: Line A: Prime LineLine B: Shared LineUsers A & B: Both have Line B (direct number) 1) Someone calls Line B and both users A and B see the caller information on their phones display. 2) User A ...
I have purchased the above conference phone from a big supplier in the US. They claim that the power cube compatible with the phone is cp-pwr-cube-4 but this cube does not fit. The vendor seem to be unable to give me the correct fitting cube. I have...
Hello, we have a CUCM 10.X, and we would like to know if we can get this kind of manipulation: if the calling number XXXX calls 3000, the real called number is 4000XXXX. That is, we would like to manipulate the called number based on the calling ...
Hi ,I am facing problem with CUCM 7.1.3 , as it is not booting and throwing the below mentioned error message. I am attaching the error snap shot also.This model server is having only one HDD of 250 GB capacity.Error Message-- "ext3-fs error (device/...
Has CME the feature to display the hunt pilot name when alerting? I realize this has been introduced in CUCM v8 as a configurable service parameter ("Display Hunt Pilot Name or DN for Hunt Group Calls When Alerting") and I am hoping that this featur...
Good Afternoon I am new to Cisco phones and i am having a real issue with provisioning the phones. I cannot get into the back end of the phone to add the provisioning details in there when i browse to the IP address i get a screen that only show...
Hello guys, I know may be i am sking this question again. But i didnt get any meaningful response so far.The problem is that we are using CUCM 8.6 at our company. And about 3000+ license.Now we are facing with licence get limit. Most of the licenses ...
| User | Count |
|---|---|
| 6 | |
| 3 | |
| 3 | |
| 3 | |
| 1 |
