Hi, I have a user unable to make calls to Kenya The user is able to make calls to other international dialed numbers as well as being apart of the call search created for international access. What are the possible reasons the user cannot make the ...
Fairly new to QOS and trying to setup a policy-map to identify traffic from an ACL. Pretty standard - but the policy does not seem to be marking traffic. We are using Avaya 9608 and 4610 IP phones. Both use DSCP 46 it looks like for both Signalin...
Am trying to configure CER for more than 1 site. Do I need to add 911, 912, 913 CTI RP for each location?
Scope:Get a spa 962 to retrieve a config file from a server using tftp or http, and properly take up the settings.Users have reportedly done it, but the documentation from cisco has nothing whatsoever.Anyway,The xml config for the phone can be reache...
Hello, I have issues with faxing through my SIP provider. But my CUBE has BRI & SIP connected. I want to route known fax numbers through BRI to avoid fax failures. UCM---SIP--CUBE--SIP/BRI---PSTN 1. How can i route certain list of numbers throug...
Hi guys,I am trying to install cucm 8.0 on my cisco mcs 7825 server for my lab at home and I am getting this error message:"MISMATCH CHASSIS: EXPECTED DL380 FOUND DL320"What that really means? Or may be that cisco mcs 7825 server platform is not desi...
Hello, I would appreciate some sort of suggestion for this inquiry----currently, we are using sort of a 'FLOOR MATS' for the handicap clients who needs to make a call to Switch board. They come on the top of a floor mat (using wheelchair) and pres...
Hi all, I am searching for a way to have the communication between VOIP-Gateway (ISR4000) and IP-Phone, between VOIP-Gateway and CUCM in the global-Routing-table, and the communication between VOIP-Gateway and SIP-provider in a VRF for security-reaso...
Hello, we recently over the summer upgraded from 8.6 to 11.5 CUCM. Recently we've had a few user cases that have complained about receiving a call internally, and then not being able to hear the other end for a couple seconds. Their sometimes seems...
Hi, Is there a way to assign calling party transformation css to all phones ? Can we done without assigning to dp-pools? How can I achieve the same functionality of calling party transformation using a translation pattern Thanks
Ok, we are having an issue where some calls come into unity from some cell phone providers we are getting a DTMF added event for every dialed digit. We have a TAC case opened with not much of a resolution, other than we are better off now than before...
Hi Guys, After upgrading CUCM from 11.0 to to 11.5.1. We are facing error . " Failed to send message to remote AXL server. Please check error log for more details." I have restarted CM AXL web service and unity ports. Please advise ? Thanks
I need some urgent help our supplier sent us the wrong KEM for our 8851 phones. They were supposed to send the 36 button KEM but instead sent the 28 Button. Now i am really struggling to add the KEM to my CUCM as an error message that blocked ...
Hi I'm trying to connect Cisco IP Communicator to UCCE 11.5 Environment any device not registered my laptop. I'm using IP communicator version 7 I think this version not supposed I have to upgrade 8 but still same issue. I'm using windows 10 Pro...
Hi I have 200 dids,and 250 phone I want to assign 50 non did numbers and assign a caller id 2430XXXX for outgoing (external) call .And another non did xxxx I want to assign caller id internaly(yyyy)and externaly 2430YYYY How can i do that? Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-12-2025 12:06 PM | ||
| 05-12-2025 06:55 AM | ||
| 05-11-2025 04:59 AM | ||
| 05-05-2025 11:16 AM | ||
| 04-30-2025 05:24 AM |
| User | Count |
|---|---|
| 5 | |
| 3 | |
| 1 | |
| 1 | |
| 1 |
