Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Can you change the remote-party-id from "no remote-party-id" to "remote-party-id" within the config on a 3825 during business hours or will this cause a bump in the phone services? Recently, our caller id stopped coming through to our phones. After ...
Коллеги, приветствую. Есть достаточно сложная схема подключения CUCM и AVAYA... Если коротко телефон cisco - SBC - PGW 2200 - Gateway - AVAYA. При звонке с CUCM на AVAYA хаотично появляется странный звук похожий на звук метронома. В обратную ст...
Good morning dears, I'm new in cisco ip telephony and after a system recovery suddenly cucm are unable to make international calls only. Both local and national calls work normally. For international calls we have route patter 9.! We have two gatew...
Hi, I have written several discussions about the problem of database replication, but now i find error in Tomcat security and start new topic. We have Cisco Unified CM System version: 9.1.2.11900-12 (Pub and Sub) and Cisco Presence For axl service ...
Hi, I am trying to change language from English (Default) to French (Canada) on Cisco 8851 phones. The CUCM version is 9.1.2 and I am intending to use below cop file as per Cisco recommendation. French (Canada) cm-locale-fr_CA-9.1...
Hi, we have a fixed broadband IMS network, and our customer (the service provider) is looking for recommendation on SIP phones that can work in this IMS solution. We have tested several other models from different manufacturers. Now we try to use Ci...
Hi I want to upgrade from CUCM 8.6 to 9.1.2 SU6, is the below ISO file the correct image for the upgrade? UCSInstall_UCOS_9.1.2.16900-2.sgn.iso - 4827.80 MB Thanks Sakun
Hi, I need to setup new sip trunk from SP dentech Netherlands. I got below information from SP. Username: 165224150@client.dentech.voipit.nl Authentication id: 165224150 (DID number) Password: password Proxy-IP: ...
Is there any setting to control incoming calls to an hunt group not to ring on the remote destination (mobile)?We have a setup where all extensions for an office are part of the hunt group. Recently routing for remote destination (mobile) was added, ...
hi i have a cluster with 4 servers (1 pub and 3 sub) installed on MCS serversi would like to upgrade to 11.5for this reason i installed 4 CUCM version 11.5 on BE7000 serversi need to migrate data and license form cucm 8.6 to 11.5what is the perfect p...
Hello all, I have an issue in regards to setting up my CUCME (10.5). I have an ISR 4331 Router running sccp. I'm trying to get Cisco 7945 / 7945G phones to run off of this router and cannot get them to either a) pull down files or b) register. I p...
I am having an issue with an IP Communicator through VPN. The IP Communicator is able to be configured and the remote user hears dial tone when going off hook, but there is no audio either way when a call gets connected. I tested cleanly on a laptop ...
Good morning, I've configured with fast track a new phone 8821 on cme 10.5. I've also configured a voice register template for Keys but it doesn't works. following the config !voice register pool-type 8821 xml-config maxNumCalls 4 xml-config busy...
Hello, Sorry for the possible crude question.. We currently have CUCM 8.6.2.22040-1 and CUCA 8.6.2.20000-76. We occasionally hire people who will never be in our office but, require a local number and access to Voice Mail. Rather then having a phys...
Hi allI am getting a bust tone into Unity either by user VM or by calling the pilot. I also show a total of 24 ports (12 for pub 12 for sub). However, when I look at the server status in cluster management I see that the port status is showing 14 on...
