Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, For past few days we are facing some issues on our IP Phones configured with SIP Extensions (Server: Elastix). The configured extensions are located in a remote location connected over IPSec VPN. We are able to ping all the phones but only one p...
Hi, These are a couple of gateways that we've inherited from a previous partner and are trying to clean up. Their ITSP requires most calls in E164, but supports non-E164 service and emergency numbers. One thing that struck me was that for each ITSP...
Hi Everyone, i have 2 problems about cisco 7821 1) Many 7821 phone doesn't register to cucm and i'm trying to register via 3g line 2) Some 7821 phone give a notice "network unavailable"
We are working on a set where CUCM 9.1 Publisher IP X.X.X.90subscribe IP X.X.X.91Partition : PT_CALL_PARKCss: STD_AccessPT_CALL_PARK is in Css: STD_AccessNew Call Park number created 3410 (This is free number) even tried for 34XXchecked Call park on ...
Hello, I want to make my network destribute VLAN dynamicly i have NPS of microsoft and i make configuration in my switchs (Cisco) and it work fine now i have some IP PHONES (Grandstream) in my network that should connecte but i don't want to authenti...
Hello All,i am currently working on a Call flow requirement which I am trying to achieve using Time of Day on CUCM.Requirement: Calls to the MainLine number are routed to a hunt group during business hours and If Busy\No Answer\Off Day the calls shou...
Dears, i have an issue for the phones registration on remote site, i have a CUCM in HQ and remote sites are registering on HQ CUCM, the link between the HQ and remote sites is 1 MB, i have 9971,8945,7841,3905 phone models, once the bandwidth is consu...
volume control issues
Hi, is there any way to avoid users to modify the RINGER volume on SPA 502G equipments?
We have several MSC 7825-I4, with UNRST_7.1.5.33900-10 on board. We needed to reinstall exact version UNRST_7.1.5.33900-10. After stat installation we had Hardware-check results: NOT SUPPORTED. We tried upgrade firmware of 7825-I4 to latest - result ...
I am running CME 11.5 and need to upgrade to11.6. After the upgrade two issues were observed that made me go back to 11.5. no time to trouble shoot the issue. One issue was the time was off on the phones. Went back to 11.5 and all was fine. The ...
Hi All, we got huawie IP phones at the branch office and 2921 voice gateway and we want to register that with our cucm 10.5 which is in HQ we would like to use SRST on branch 2921 voice gateway. now my main concern is is it possible to do this usin...
Just trying to configure Meetme conferencing in CME, refering to the below documentation from Cisco.http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeconf.html#wp1020601Is there a better documentation available for Vers...
Hey everyone Just wanted to check if anyone could point me to some documents regards adding and configuring a side car to a 7962 phone running on CME?
Hi there, I have some questions regarding my PSTN calls. We have a CUCM and 2x AS5400 gateway with 4 PRIs configured in a route list. When a user calls a switched off cell phone , it takes forever to receive a busy tone. Looking at the debugs , we...
| User | Count |
|---|---|
| 12 | |
| 8 | |
| 8 | |
| 4 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
