Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Everyone! We have two sets of CP-8945 one with hardware revision 4 and other with hardware revision 3. Hardware revision 3 (with firmware 9.3.4.17) is working well with asterix but for hardware revision 4 (with firmware 9.4.2) has issues with...
Hi everyone, can someone help me with my issue. One of the phone is our office suddenly goes Unprovisioned. Upon checking in CUCM it was unregistered. I tried to register it again by deleting the phone and adding the same phone but to no avail. It wa...
Hi , Is the below link is moved or broken http://www.cisco.com/cisco/software/navigator.html?mdfid=268437892&flowid=5293 I was trying to download firmware for our Cisco 8941 cmterm-8941_8945-sccp.9-3-4-12.zip Is there an alternative ...
hey there, i have two 7841 sip phones and successfully registered on the CME as SIP phones but i can't, Below is info regarding the current configuration,Router# show run | section dial-peerdial-peer voice 1 voipdestination-pattern 1000session target...
hey there, i have two 7841 sip phones and successfully registered on the CME as SIP phones but i can't, Below is info regarding the current configuration Router# show run | section dial-peerdial-peer voice 1 voipdestination-pattern 1000session target...
So the active load firmware on the 7841 is sip78xx. but i can't find the SIP configuration on the phone it self neither on the web UI,when i load it with another sip firmware through tftp, it asks "press a key to change the service mode" and when i p...
Hi, just migrated off some very old CM equipment and went to a fully Cloud PBX (Nextiva). One of the challenges is all of our employees have been dialing "9" to get an outside line for 20 years. Nextiva's standard configuration does not require eve...
Hi We recently cross an issue where one way audio when answer from hunt queued calls and call flow as below: ITSP ---sip---> CUBE(SP) --- sip--> CUCM --- sip---> ip phone PSTN caller 1 call the hunt and answer by IP phone with 2 way audio. Then 2nd ...
Blind transfer works, if there is only one active call. But if a user is on a call, and a second call comes in, then they lose the ability to blind transfer either call. This is on a 8861 with the Multiplatform Firmware.
May I know how to upload custom ringtone for 3905 Model phones? is it supporting it from Ringlist.xml? I cannot see the ringtone mentioned in ringlist.xml. We would like to add our own ringtone to 3905 model...
hello everyone,My customer has a CME with the feature of Extension Mobility configured working just fine.But in the IP Phone when he will enter with the user ID and password , he thinks very difficult to have to enter the password as an sms style ( A...
Hellow.Is there a way on 12.5 CUCM, two Fanvil Devices, which are registered with the same DN to behave as one. For Example, if one of the two fanvil devices answers the call and then put it on Hold, the other to have the ability to take the call and...
Hi,We came across weird issues. Computers connected to Switch are not working correctly when connected via cisco desk phone - showing unidentified network. Without desk phone computers working fine. Issue started +- a week ago.port config interface G...
Good day, I have the following network architecture:Internet < -- > FortiGate < -- > Cisco Router (CCME) < -- > Cisco IP Phone < -- > PCThe DHCP server must be activated on the FortiGate, dose this is possible?Best regards,
Started getting disconnect code 41 after 2 rings on only 1 extension. If you answer the call before the 2nd ring the call completes as normal. All other extensions work fine.See call detailssuccessful callMessage DetailsSENDER: 172.27.199.20GUID: 8b...
