11-28-2013 12:19 AM - edited 03-16-2019 08:37 PM
Hi all,
I am using CUBE as SIP gateway. When i run "show call active voice brief" command, all the calls have the same call id 1 or 0. So it is hard to track calls at the gateway. Is it normal? Does anybody know the reason of that?
12-07-2013 11:04 AM
Please, add an example of the output of the command.
Regards.
12-07-2013 12:07 PM
Hi.
If you are using sip-ua to connect to a TSP, you can use show sip-ua calls brief
HTH
Carlo
Please rate all helpful posts
"The more you help the more you learn"
12-09-2013 02:40 AM
Hi Carlo,
How can i see the dial-peers used for the call if i use "show sip-ua calls brief"?
Regards,
Safak
12-09-2013 09:14 AM
You can see used SP with show voice call status.
12-08-2013 11:38 PM
Sample output:
-------------------------------------
0 : 69572 09:34:05.177 Turkey Mon Dec 9 2013.1 +5300 pid:1 Answer XXXX active
dur 00:00:03 tx:169/27040 rx:166/26560
IP
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
0 : 69573 09:34:05.187 Turkey Mon Dec 9 2013.1 +5290 pid:106 Originate XXXXXXXXXXX active
dur 00:00:03 tx:167/26720 rx:170/27200
IP
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
12-09-2013 02:35 AM
Here is another sample output from another sip gateway(this is not CUBE, it is AS5400)
0 : 360645 12:32:18.042 Turkey Mon Dec 9 2013.1 +5800 pid:1 Answer XXXX active
dur 00:00:17 tx:1/160 rx:870/139200
IP
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
0 : 360646 12:32:18.094 Turkey Mon Dec 9 2013.1 +5750 pid:106 Originate XXXXXXXXXXX active
dur 00:00:17 tx:871/146328 rx:259/41122
Tele 7/1:D (360646) [7/1.1] tx:17430/3560/0ms g711ulaw noise:-66 acom:45 i/0:-66/-42 dBm
12-09-2013 09:15 AM
I've some AS5400 but I see call ID without problem. Do you have the same IOS version on boot AS and CUBE?
12-09-2013 11:24 PM
I have IOS version of 15.1(4)M6 on AS5400 and 15.1(4)M4 on CUBE(3925)
12-10-2013 03:08 AM
Incoming calls are generated from a CUCM?
12-10-2013 04:10 AM
Yes, calls are generated from CUCM. When we generate the call from PSTN we get a usual call ID for the call legs. Additionallay, not only null, i also see 1 as the call id when the call is generated from CUCM:
From 3925:
1 : 77849 13:55:21.747 Turkey Tue Dec 10 2013.1 +14450 pid:1 Answer XXXX active
dur 00:00:20 tx:1045/167200 rx:1043/166880
IP
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1 : 77850 13:55:21.747 Turkey Tue Dec 10 2013.2 +14450 pid:106 Originate XXXXXXXXXXX active
dur 00:00:20 tx:1043/166880 rx:1045/167200
IP
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
From AS5400:
1 : 378233 14:03:39.836 Turkey Tue Dec 10 2013.1 +8060 pid:5 Answer XXXX active
dur 00:00:19 tx:1/160 rx:982/157120
IP 10.45.100.64:17584 SRTP: off rtt:0ms pl:13840/0ms lost:0/0/0 delay:55/55/65ms g711ulaw TextRelay: off
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1 : 378234 14:03:39.884 Turkey Tue Dec 10 2013.1 +8010 pid:106 Originate XXXXXXXXXXX active
dur 00:00:19 tx:983/165144 rx:291/46242
Tele 7/3:D (378234) [7/3.2] tx:19680/4200/0ms g711ulaw noise:-68 acom:45 i/0:-67/-32 dBm
I couldn't find out what causes this.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: