cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
400
Views
0
Helpful
3
Replies

call outside directly without press 9 or 0

Yazen Alaa
Level 1
Level 1

Hi

i have H323 voice  Gateway with E1 configuration , by question is how can i call outside directly without press 9 or 0 then + mobile or home or international number ???

Ex. 967205444

i need without press 9

67205444

there is steps or notepad configuration that help me to do it ???

thanks and regards

3 Replies 3

Jonathan Schulenberg
Hall of Fame
Hall of Fame

That all comes down to your dial-peer configuration. There is a reason why most PBX systems use an off-net code: to distinguish between internal extensions and off-net patterns. If you have four-digit extensions in the 2XXX range and dial a PSTN number starting with 2T you will have a problem; IOS will match the internal pattern first.

Look at your dial-peers, specifically the destination-pattern sub-command. It should start with 9 today. You can remove the 9 and just have whatever comes after it such as 67T. Just remember that any explicitly-matched digits are stripped. If you match 67T then you would need to prefix 67 to get the full number sent out to the PSTN.

thank for ur reply

you mean i have to remove 9 from this dial peer and from route pattern in the call manager

dial-peer voice 10 pots

destination-pattern 9

direct-inward-dial

port 1/0:15

please this is the confoguration i have


User Access Verification

Password:
universeE1>ena
Password:
universeE1#sh run
Building configuration...

Current configuration : 1573 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname universeE1
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$Gh4n$9gV0GYwHeIXgd4K0hqG0l.
!
no aaa new-model
!
resource policy
!
no network-clock-participate slot 1
no network-clock-participate wic 0
voice-card 1
!
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
no ip domain lookup
no ftp-server write-enable
isdn switch-type primary-net5
!
!
!
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
!
!
!
!
!
!
!
!
!
!
!        
!
controller E1 1/0
pri-group timeslots 1-31
!
!
!
interface FastEthernet0/0
ip address 192.168.200.3 255.255.255.0
duplex auto
speed auto
!
interface Serial1/0:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bchan-number-order ascending
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.200.5
!
ip http server
!
!
!
control-plane
!
!
!
voice-port 1/0:15
!
!
!
!
!
dial-peer voice 1 voip
destination-pattern ...
session target ipv4:192.168.200.1
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 10 pots
destination-pattern 9
direct-inward-dial
port 1/0:15
!
dial-peer voice 3 voip
destination-pattern 550
session protocol sipv2
session target ipv4:192.168.180.221
dtmf-relay rtp-nte
codec g711ulaw
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
no vad
!
gateway
timer receive-rtp 1200
!
sip-ua
!
!
line con 0
line aux 0
line vty 0 4
password c
login
!
!
end

universeE1#

Be very careful not to create overlaps here, as Jonathan stated there is a reason most companies use off-net access code, once you get rid of the off-net access code your options for internal extensions are limited depending on what country/state/city your deployments are in and how you dial PSTN.

HTH,

Chris

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: