04-08-2014 01:57 AM - edited 03-16-2019 10:24 PM
Hello,
I have configured my MGCP gateway to register with my CUCM. However, only calls from CUCM is successful whereas calls from simulated PSTN fails.
Please find attached debugs and gateway configs.
Appreciate your comments. Thanks.
04-08-2014 03:04 AM
Hi, the called number received from simulated PSTN is "Called Party Number i = 0xC1, '5553003' " but your extension is 2003 not 3003. that is causing the issue.
If you configure 3003 instead of 2003, it would ring the phone. Please check.
04-08-2014 03:09 AM
I've tried, its not ringing.
04-08-2014 03:16 AM
I only got it working if I change the external phone mask to 2XXX and the DN to 2XXX, but I wanted to use DN 3XXX as it will differentiate my HQ phone from my BR phone
04-08-2014 03:29 AM
It is confusing. can you brief more on this please?
04-08-2014 03:41 AM
Basically my HQ uses DN 2XXX, with external mask +555115552XXX, BR uses DN 3XXX with external mask +665215553XXX, if I call 5553XXX, it will fail, however, if I change it to 2XXX for both DN and external mask it works. I am also getting confused.
04-08-2014 03:48 AM
External mask is nothing to do with inbound calls.
can you check if there is any translation pattern (beginning with 555) to convert the number from 5552XXX to 2XXX?
What I guess is, instead of passing only 4 significant digits, all digits are received & processed in CUCM.
04-08-2014 04:05 AM
I thought translation pattern is call from CUCM phones to PSTN. Correct me if I am wrong, my knowledge in voice not that good, I could not see any translation pattern beginning with 555. As for Called party transformation pattern, I could see some pattern,
\+55511.XXXXXXX with predot discard digits.
and calling party transformation pattern with
\+55511.5552XXX
\+55511.XXXXXXX
also with predot discard digits
04-08-2014 04:09 AM
it is now better to collect CCM traces for a test call for BR site. also collect the debug isdn q931 log from the MGCP gateway at the same time.Please include the calling & called number.
04-08-2014 04:09 AM
Without going deeper in problem (we already have so much confusing info ) - why don't you just replicate HQ translations which you mentioned for your BR location with appropriate modifications?
BR,
Dragan
04-08-2014 07:48 AM
Hey guys, issues solved. Just a silly cable issue, I changed the cable and everything works miraculously.
04-08-2014 02:24 AM
This isdn debug - it it for outgoing call?
And ccapi - for incoming?
Can you give a little bit more details...
BR,
Dragan
04-08-2014 02:35 AM
Both the ISDN and ccapi is for outgoing.
Please find ISDN debug for MGCP GW
*Apr 8 17:30:58.131: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0095
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x4180, '5554444'
Plan:ISDN, Type:Subscriber(local)
Called Party Number i = 0xC1, '5553003'
Plan:ISDN, Type:Subscriber(local)
*Apr 8 17:30:58.143: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8095
Cause i = 0x8081 - Unallocated/unassigned number
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide