cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
2114
Views
0
Helpful
10
Replies
Randy Haddon
Beginner

calls not completing on Cisco VG204

I have setup a VG204 for one of our departments to use for their credit card machine and a postage machine, there is aslo a fax machine and a cordless phone on this device and they work okay.  when they try and process a credit card or add postage the call initiates but eventually fail.  I have the voice-port timeouts set to 60 (initial and interdigit) and timeouts ringing infinity.  Is there any special settings on the call manager or on the gateway?

Thanks,

Randy

10 REPLIES 10
troullier00
Beginner

Can you connect a phone to the line and make calls? I would imagine that the ATM and Postage Machine need tone set unlike your analog fax line to properly pass tones for card processing. Could you post the 204 configuration for all 4 lines?

Sent from Cisco Technical Support iPhone App

How are the calls getting to the PSTN?  Is it POTS lines, PRI, SIP, or something else? 

If SIP, the codec could be the issue. 

We are using a PRI.

Yes I can hook up a regular phone and it works just fine.

here is the config:

no aaa new-model

ip source-route

ip cef

no ipv6 cef

stcapp ccm-group 1

stcapp

stcapp feature access-code

stcapp feature speed-dial

voice service voip

h323

voice-card 0

archive

log config

  hidekeys

interface FastEthernet0/0

ip address 10.10.X.X 255.255.255.0

speed auto

full-duplex

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

ip default-gateway 10.10.X.X

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 10.10.X.X

no ip http server

control-plane

voice-port 0/0

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

voice-port 0/1

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

voice-port 0/2

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

voice-port 0/3

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

ccm-manager fax protocol cisco

ccm-manager config server 10.10.X.X 

ccm-manager config

ccm-manager sccp local FastEthernet0/0

ccm-manager sccp

       

sccp local FastEthernet0/0

sccp ccm 10.10.X.X identifier 1 version 4.1

sccp ccm 10.10.X.X identifier 2 version 4.1

sccp

sccp ccm group 1

associate ccm 1 priority 1

associate ccm 2 priority 2

dial-peer voice 999000 pots

service stcapp

port 0/0

dial-peer voice 999001 pots

service stcapp

port 0/1

dial-peer voice 999002 pots

service stcapp

port 0/2

dial-peer voice 999003 pots

service stcapp

port 0/3

no aaa new-model

ip source-route

ip cef

no ipv6 cef

stcapp ccm-group 1

stcapp

stcapp feature access-code

stcapp feature speed-dial

voice service voip

h323

voice-card 0

archive

log config

  hidekeys

interface FastEthernet0/0

ip address 10.10.X.X 255.255.255.0

speed auto

full-duplex

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

ip default-gateway 10.10.X.X

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 10.10.X.X

no ip http server

control-plane

voice-port 0/0

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

voice-port 0/1

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

voice-port 0/2

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

voice-port 0/3

timeouts initial 60

timeouts interdigit 60

timeouts ringing infinity

ccm-manager fax protocol cisco

ccm-manager config server 10.10.X.X 

ccm-manager config

ccm-manager sccp local FastEthernet0/0

ccm-manager sccp

sccp local FastEthernet0/0

sccp ccm 10.10.X.X identifier 1 version 4.1
sccp ccm 10.10.X.X identifier 2 version 4.1

sccp

sccp ccm group 1

associate ccm 1 priority 1

associate ccm 2 priority 2

dial-peer voice 999000 pots

service stcapp

port 0/0

dial-peer voice 999001 pots

service stcapp

port 0/1

dial-peer voice 999002 pots

service stcapp

port 0/2

dial-peer voice 999003 pots

service stcapp

port 0/3

Hi Randy

Common cause of this kind of failure is clock slips on your PRI. Check the status of the controller and see it is reporting any slips. Voice isn't impacted by this kind of thing, however modem / fax is.

HTH. Barry

Thanks for the info I checked the controller and it is showing that it is up and has 0 slips secs.

I am experiencing something similar and looking for a way to fix it. The credit card machine at my location works sometimes but occasionally times out.

The output of "sh controller T1" command shows:

T1 0/0/0 is up.

  Applique type is Channelized T1

  Cablelength is long 0db

  No alarms detected.

  alarm-trigger is not set

  Soaking time: 3, Clearance time: 10

  AIS State:Clear  LOS State:Clear  LOF State:Clear

  Version info FPGA Rev: 08121917, FPGA Type: PRK1

  Framing is ESF, Line Code is B8ZS, Clock Source is Line.

  CRC Threshold is 320. Reported from firmware  is 320.

  Data in current interval (446 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     22 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Total Data (last 24 hours)

     0 Line Code Violations, 3 Path Code Violations,

     3864 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

     1 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Is there something I can do to fix the problem? Any advice is greatly appreciated!

Thanks,

Lisa

This is often asked

network-clock-select 1 t1 0/0/0

Thank you Paolo. I just added that command to my configuration and cleared the counters (I was showing lots of "slips"). I'll monitor the VG for errors and have someone run another credit card payment.

I very much appreciate your very quick response!

You're welcome, please remember to rate useful posts clicking on the stars below.

Create
Recognize Your Peers
Content for Community-Ad