cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1143
Views
0
Helpful
5
Replies

CCNA Voice Collaboration LAB

mekeniabe
Beginner
Beginner

I bought a a Voice-enabled Cisco 2821 ISR Router for my Cisco CCNA Voice Collaboration LAB loaded with Cisco Unified CUCME/CME 8.6 (Call Manager Express) and CCP 2.7.IOS version is Mainline 15.1.4.M10 Adv. Enterprise Services (c2800nm-adventerprisek9-mz.151-4.M10.bin)

This Router includes the following Voice Cards and Modules:

- FXO Analog Card (needed to make Phone Calls outside the LAN)
- FXS Analog Card (needed to connect an Analog Phone)
- PVDM2 Module (needed to enable both Voice Cards)

I got everything working with my LAN Switch creating a LAN-based Phone Network.

All configurations for Inbound and Outbound Rule are all working.

The "connection" command for the Inbound Rule specifies a private-line, automatic ring doqwn (PLAR) connection, off premise connection (OPX) and to forward the incoming call from PSTN to the extension number say 2001.

In other words, if someone is calling my PSTN Phone number at home say 415-810-2907, the call is forwarded to extension 2001.

Is it possible for a single PSTN line ( not a DID trunk ) since this is just for Lab PURPOSES to call the extension number directly without dialing the the 415-810-2907? I mean I will dial 415-810-2001 instead of my landline 415-810-2907. If so how will I configure my router?

Thanks and regards,

Jerry S. 

 

 

1 Accepted Solution

Accepted Solutions

Hi

looks like you are using FXO ... then whatever call is ringing on this FXO port it will be routed to the number specified in the connection plar command under the voice port.

The Only way is to have the Analog Line from service provider with the same last 4 digits as your extension to call it ... but you will have to add a connection plar command under the voice port again...

Cheers,

M

View solution in original post

5 Replies 5

Hi

looks like you are using FXO ... then whatever call is ringing on this FXO port it will be routed to the number specified in the connection plar command under the voice port.

The Only way is to have the Analog Line from service provider with the same last 4 digits as your extension to call it ... but you will have to add a connection plar command under the voice port again...

Cheers,

M

yes, you are right. Though I  got all my objectives  using my lab kit with 2 analog phones connected to my fxs ports, pstn line to fxo port and the 2  Cisco IP Phones Phones .

Out of curiosity, would it be possible to call the extensions lines be it analog phones or the ip phones directly instead of the analog line telephone number?  Is there any configuration to link the analog line #  with the extensions number that instead of dialing the analog phone number, you can dial directly the extension number.

Thanks.

Hi Mekeniabe,

i guess that you need to add analog phone connected to FXS Port into your cucm cluster ...

Then you need to configure it with an extension in CME or CUCM server but using this way your analog phones wont be part of PSTN Phones and you will not use FXO Ports ..

Please Post your configuration to understand the scenario ..

Cheers,

MO Giacobbe

MCSD, SCJP, CCIE Collaboration #50401

Hi Mohannad,

I am just starting  studying CCNA Voice ( self study ) and I do really appreciate you for your time in replying to my query. Thank you so much. Below is the configuration which I deleted some of the part which is not necessary in my questions.

When a call comes in on the FXO port, it is sent to pilot 2001 (ephone-dn 50) which is configured as the 2nd button on the two phones ( 2:50 ). The two Cisco Phones will then ring simultaneously.

Therefore, If I make a call from my  cellphone and dial my PSTN line ( see attached diagram ) 1-415-756-3864,  the call is routed both on the 2 IP Phones, ext's 1001, 1002.

Just for curiosity or further studies, is there a configuration  on this router to  dial directly the extension numbers , e.g. 1001 and 1002  instead of dialing the pstn line # 1-415-756-3864.

say I can  dial 1-415-756-1001 directly or 1-415-756-1002 if I want.

Thanks.

2811#show run

Building configuration...

Current configuration : 11772 bytes

!

version 15.1

hostname C2811

!

voice service voip

ip address trusted list

ipv4 0.0.0.0 0.0.0.0

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

sip

bind control source-interface FastEthernet0/0.25

bind media source-interface FastEthernet0/0.25

registrar server expires max 3600 min 120

!

!

voice register global

mode cme

source-address 172.25.140.1 port 5060

max-dn 40

max-pool 42

tftp-path flash:

create profile sync 000490728535965A

!

voice register dn 1

number 2001

allow watch

name PH-2001

label 2001

mwi

!

voice register dn 2

number 2002

allow watch

name PH-2002

label 2002

mwi

!

voice register dn 3

number 2003

allow watch

name PH-2003

label 2003

mwi

!

!

!

voice-card 0

!

tftp-server flash:/Ringtones/KotoEffect.raw alias KotoEffect.raw

voice-port 0/0/0

connection plar opx 2001

caller-id enable

!

voice-port 0/0/1

!

voice-port 0/1/0

caller-id enable

!

voice-port 0/1/1

!

voice-port 0/1/2

!

voice-port 0/1/3

!

!

!

mgcp profile default

!

!

dial-peer voice 5 pots

destination-pattern 91..........

port 0/0/0

forward-digits 11

!

dial-peer voice 10 pots

destination-pattern 4001

port 0/1/0

!

dial-peer voice 20 pots

destination-pattern 4002

port 0/1/1

!

dial-peer voice 7 pots

destination-pattern 1000

port 0/0/0

!

!

!

!

telephony-service

moh-file-buffer 2000

max-ephones 30

max-dn 50

ip source-address 172.25.140.1 port 2000

!

ephone-dn 1

number 1001

label Sunga

description Jerry

name Mustang

hold-alert 30 originator

!

!

ephone-dn 2

number 1002

label 1002

description Portia

name Phone 2

hold-alert 30 originator

!

!

ephone-dn 3

number 1003

label 1003

--More--

Jun 30 04:03:48.431: %IPPHONE-6-REG_ALARM: 25: Name=SEP0015F95041A9 Load=8.1(2.0) Last=Initialized

Jun 30 04:03:48.431: %IPPHONE-6-REGISTER: ephone-1:SEP0015F95041A9 IP:172.35.140.12 Socket:1 DeviceType:Phone has registered.

description Phone 3

name Phone 3

hold-alert 30 originator

!

!

ephone-dn 14

number 6112

name Sales

paging ip 239.1.1.1 port 2000

!

!

ephone-dn 50

number 2001

trunk 1000 monitor-port 0/0/0

!

!

ephone 1

device-security-mode none

description Home Office

mac-address 0015.F950.41A9

paging-dn 14

button 1:1 2:50

!

!

!

ephone 2

device-security-mode none

description Mustang Office

mac-address 0015.F92E.D21A

paging-dn 14

button 1:2 2:50

!

!

!

C2811#

 

The only you could dial 1-415-756-1001 or 1-415-756-1002 from outside network (your cellphone/PSTN) is by getting those numbers from your service provider.

Internally, you can achieve this by translation rules.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers