cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
8202
Views
10
Helpful
7
Replies

Cisco IP Phone 7811 unprovisioned

Ahmed habib
Level 3
Level 3

I added the 7811 IP Phone to CME 11.5 and it took an IP but still say unprovisioned 

Here is the configuration 

1 Accepted Solution

Accepted Solutions

R0g22
Cisco Employee
Cisco Employee
Add the following -

voice register pool 1
num 1 dn 1

voice register global
create profile

View solution in original post

7 Replies 7

R0g22
Cisco Employee
Cisco Employee
Add the following -

voice register pool 1
num 1 dn 1

voice register global
create profile

OK, The phone become registered but these errors are showed in debug 

What is the meaning ?

 


cisco#debug ccsip err
cisco#debug ccsip error
SIP Call error tracing is enabled
cisco#
*Mar 6 07:37:27.987: //-1/0E0711568035/SIP/Error/sipSPIFlushDeferredQueue:
Invalid deferredQueue
*Mar 6 07:37:28.011: //-1/0E0ABCE48036/SIP/Error/sipSPIFlushDeferredQueue:
Invalid deferredQueue
*Mar 6 07:37:28.151: //-1/xxxxxxxxxxxx/SIP/Error/ccsip_reg_search_call_id_table:
No entry found in sipCallID Table
*Mar 6 07:37:28.151: //-1/xxxxxxxxxxxx/SIP/Error/sipSPI_validate_own_ip_addr:
ReqLine IP addr does not match with host IP addr
*Mar 6 07:37:28.155: VOICE REGISTER POOL-1 has registered. Name:SEP00279024A9E7 IP:192.168.70.2 DeviceType:Phone

*Mar 6 07:37:28.155: %SIPPHONE-6-REGISTER: VOICE REGISTER POOL-1 has registered. Name:SEP00279024A9E7 IP:192.168.70.2 DeviceType:Phone

*Mar 6 07:37:28.155: //-1/xxxxxxxxxxxx/SIP/Error/ccsip_reg_locate_in_pattern_table:
***No entry found in Destination pattern Table
*Mar 6 07:37:28.155: //-1/xxxxxxxxxxxx/SIP/Error/sipSPIGetDialogParamStr:
Invalid parameters
*Mar 6 07:37:29.135: //-1/xxxxxxxxxxxx/SIP/Error/sipSPILocateSubscribeDialogSCB:
Could not find scb for response
*Mar 6 07:38:00.159: //1/0E10D7A58037/SIP/Error/sipSPIFlushDeferredQueue:
Invalid deferredQueue

You can ignore those. Not everything you see in the logs is relevant. It would be difficult to explain every line in that log, here at least.

I had to replace 7911 with 7811 series recenlty.

MAC address has been changed to new one and all configuration seems to be ok but phone stays unprovisioned.

I have call manager configured on old 3845-K9 - It's been done many years ago.I've found config xml's for 79 series but nothing for 78...

 

Could You suggest anything?

 

Many thanks,

 

fisher

@fisher_radionavYou hav to check IF CME Version support 7811 Type or not first

You can't configure 78xx phones on 38xx CMEs. 38xx can't run the required
IOS

**** please remember to rate useful posts

Thank You kindly for quick response and support!

Regards,

fisher
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: