05-04-2015 09:29 AM - edited 03-17-2019 02:53 AM
Does anyone know if the newer ISR 4K series of routers is backwards compatible with CUCM 8.6 using MGCP; and if so, is a COP file required for CUCM?
After doing a little research it appears that the 4400 series does not support FXO/FXS lines and looks like it is primarily being marketed as a CUBE router used for establishing SIP trunks to an ITSP. I am mainly curious about the 4351 router and its capabilities as a voice gateway.
Any info regarding MGCP compatibility using T1/PRIs in CUCM 8.6 would be appreciated! Thanks again.
This is all I could find on Cisco's website:
05-04-2015 10:17 AM
Hi,
Please check the following enhancement for MGCP support
https://tools.cisco.com/bugsearch/bug/CSCuo85914/?reffering_site=dumpcr
Symptom:
To add support of ISR 4351, ISR 4331 and ISR4321 platform in UCM. User can provision ISR4351, ISR4331 and ISR4321 and NIM T1/E1 cards on UCM UI.
Conditions:
New enhancement done
Workaround:
New enhancement done
Known Fixed Releases: | (8) |
05-04-2015 10:43 AM
Thanks Manish, I found the COP file you were referencing.
05-04-2015 07:28 PM
The 8.6 version listed here is an ES version.
Manish
05-05-2015 08:30 AM
Can you send me a link where I can download that engineering special, or do I need to open a TAC case?
05-05-2015 08:34 AM
You need to contact TAC for publishing the link to download ES.
Manish
09-05-2016 11:09 PM
Hey Guys,
i understand this post is an year old, but I am trying to add a ISR 4351 to CUCM 10.5.1.10000-7 but cannot find it listed on the UI.
Can someone guide me if i need to install a cop file if so where can i locate it? Or a TAC case is the only way to do it?
Regards
Alok
09-05-2016 11:26 PM
Hi Alok,
Please upgrade to 10.5(2.10000.5) or higher as per the following
https://bst.cloudapps.cisco.com/bugsearch/bug/CSCuo85914
Manish
09-05-2016 11:48 PM
[+5] to Manish
with CUCM version 10.5.1.10000-7, u would be able to add only ISR 4431 and 4451.
with CUCM 10.5.2.10000-5, u would be able to add ISR 4321, 4331,4351 , 4431 and 4451.
regds,
aman
09-06-2016 12:03 AM
10-06-2016 12:35 AM
Hi Manish,
Any idea if Cisco 4300 can still be supported with CUCM version 8.5?
Thanks,
Janice
10-06-2016 12:57 AM
Hi Janice,
Unfortunately I don't see its support on 8.5 and don't think it will ever be possible in the future
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/uc_system/unified/communications/system/versions/IPTMtrix.html#wp1016708
You should consider upgrading cucm to 8.6.
HTH
Manish
03-13-2017 02:42 PM
At the time of this writing TAC no longer seems interested in supporting 4300 (or 4400) series routers as MGCP gateways in CUCM 8.6.
I was referred to table 6 in the link below. You'll find support starts in 9.1.2.
08-24-2017 11:15 AM - edited 08-24-2017 11:17 AM
Hi,
Is it possible to configuring router 4321 with the procotol H.323/SIP with CUCM 8.6 ?
Does anyone know something like that ?
This link table 6 give the information that the router 4321 just work with the version 9.1.2 and above.
Thanks,
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: