cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

661
Views
0
Helpful
5
Replies
Highlighted
Beginner

CISCO2921/K9 w/ PVDM3-64

Hi -

New SRST gateway I'm installing has PVDM3-64 installed. When booting the router I get the following warning:

Warning! DSPs1, 2,  in slot 0 are using non-default firmware from flash:

This is not recommended, the default version is 26.3.6

But when I do a show voice dsp detailed the installed DSP shows the correct firmware it says I should be using.

EOGrvMUSshawn01#show voice dsp detailed

DSP  DSP                DSPWARE CURR  BOOT                         PAK     TX/RX

TYPE NUM CH CODEC       VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT

==== === == ======== ========== ===== ======= === == ========= == ===== ============

----------------------------FLEX VOICE CARD 0 -----------------------------

                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending

LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending

DSP    DSP                 DSPWARE CURR  BOOT                         PAK   TX/RX

TYPE   NUM CH CODEC        VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT

====== === == ========= ========== ===== ======= === == ========= == ==== ============

SP2600 001 01 None          26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 02 None         26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 03 None          26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 04 None          26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 05 None         26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 06 None          26.3.6 idle  idle      0  0                 0          0/0

EOGrvMUSshawn01#show inv | inc PVDM3      

NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"

PID: PVDM3-64          , VID: V01 , SN: FOC16311779

Any suggestions to why this warning message is showing and if it will cause problems is much appreciated!

Thanks,

Tom Fredericks      

5 REPLIES 5
Hall of Fame Master

Re: CISCO2921/K9 w/ PVDM3-64

Do you have other firmware files defined on flash?

Can you post "sh flash"?

Sent from Cisco Technical Support iPhone App

Beginner

CISCO2921/K9 w/ PVDM3-64

Not that I can see. Just have the default files that come with the router and the IOS bin.

EOGrvMUSshawn01#show flash

-#- --length-- -----date/time------ path

1         2903 Aug 14 2012 02:09:04 cpconfig-29xx.cfg

2      3000320 Aug 14 2012 02:09:16 cpexpress.tar

3         1038 Aug 14 2012 02:09:24 home.shtml

4       122880 Aug 14 2012 02:09:32 home.tar

5      1697952 Aug 14 2012 02:09:46 securedesktop-ios-3.1.1.45-k9.pkg

6       415956 Aug 14 2012 02:09:58 sslclient-win-1.1.4.176.pkg

7         2962 Aug 22 2012 15:01:38 -0

8     62759344 Aug 22 2012 15:17:08 c2900-universalk9-mz.SPA.150-1.M2.bin

9        14042 Aug 22 2012 15:22:36 -1

10       11901 Aug 24 2012 14:14:50 -2

11       14021 Aug 24 2012 14:35:16 -3

12       14021 Aug 24 2012 14:43:04 -4

188407808 bytes available (68079616 bytes used)

Hall of Fame Master

CISCO2921/K9 w/ PVDM3-64

Update IOS and check again.

Beginner

CISCO2921/K9 w/ PVDM3-64

Hi Paolo -

I have tried with two different IOS versions and gotten the same result.

c2900-universalk9-mz.SPA.150-1.M8.bin

c2900-universalk9-mz.SPA.150-1.M2.bin

Hall of Fame Master

CISCO2921/K9 w/ PVDM3-64

Then if you no operational problem, you can ignore the message.

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here