cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
810
Views
0
Helpful
3
Replies
Beginner

CME 2851 - Dropping calls on primary DN when shared line is answered

Problem Summary

Shared line 7004 members have a button called 'MAPS 5' assigned to button 2 on handsets.

For no apparent reason and after no identified changes to the CME (2851), when users (members of 7004 shared line) are on a call on their primary line, if a call comes in on the shared number (7004) and is answered, all calls on the users (shared line 7004 members) primary lines are cut off (dead silence).

Suspicions

I suspect there is a but in the software bug in IOS release 12.4(20)T4 which is the cause of this, but before I sugest to the client an upgrade I just wanted to get anybodys thoughts on the matter.

Has anyone had any experince with problems similar to this?

Below are exerts from the config and I have attached the full config as well.

Thank you.

DGW

!---------------------------------------------------
ephone-dn  104  dual-line
number 7004
pickup-group 99
label MAPS 5
name MAPS 5
huntstop channel
no huntstop
hold-alert 60 originator
!-----------------------------------------------------
ephone-hunt 1 sequential
pilot 7051
list 7021, 7004
final 7009
timeout 25, 15
!---------------------------------------------------
MNPR001#show ephone-hunt
Group 1
    type: sequential
    pilot number: 7051, peer-tag 20258; expanded-number 64367051, peer-tag 20259
    list of numbers:
        7021, aux-number A7051A0000, # peers 4, logout 0, down 0
            peer-tag  dn-tag  rna  login/logout  up/down
             [20257     134    0       login      up  ]
             [20256     133    0       login      up  ]
             [20255     132    0       login      up  ]
             [20254     131    0       login      up  ]
        7004, aux-number A7051A0001, # peers 1, logout 0, down 0
            peer-tag  dn-tag  rna  login/logout  up/down
             [20260     104    0       login      up  ]
    final number: 7009
    preference: 0
    preference (sec): 9
    timeout: 25, 15
    E.164 register: yes
    auto logout: no
    stat collect: no
    callqueue display: continuously
    debug: no

!---------------------------------------------------
MNPR001#show dialplan number 7004
Macro Exp.: 7004

VoiceEncapPeer20193
        peer type = voice, system default peer = FALSE, information type = voice,
        description = `',
        tag = 20193, destination-pattern = `7004$',
        voice reg type = 0, corresponding tag = 0,
        allow watch = FALSE
        answer-address = `', preference=0,
        CLID Restriction = None
        CLID Network Number = `'
        CLID Second Number sent
        CLID Override RDNIS = disabled,
        rtp-ssrc mux = system
        source carrier-id = `', target carrier-id = `',
        source trunk-group-label = `',  target trunk-group-label = `',
        numbering Type = `unknown'
        group = 20193, Admin state is up, Operation state is up,
        incoming called-number = `', connections/maximum = 0/unlimited,
        DTMF Relay = disabled,
        URI classes:
            Destination =
        huntstop = disabled,
        in bound application associated: 'DEFAULT'
        out bound application associated: ''
        dnis-map =
        permission :both
        incoming COR list:maximum capability
        outgoing COR list:minimum requirement
        Translation profile (Incoming):
        Translation profile (Outgoing):
        incoming call blocking:
        translation-profile = `'
        disconnect-cause = `no-service'
        advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
        mailbox selection policy: none
        type = pots, prefix = `',
        forward-digits 0
        session-target = `', voice-port = `50/0/104',
        direct-inward-dial = disabled,
        digit_strip = enabled,
        register E.164 number with H323 GK and/or SIP Registrar = TRUE
        fax rate = system,   payload size =  20 bytes
        supported-language = ''
        preemption level = `routine'
        bandwidth:
            maximum = 64 KBits/sec, minimum = 64 KBits/sec
        voice class called-number:
            inbound = `', outbound = `'
        dial tone generation after remote onhook = enabled

        Time elapsed since last clearing of voice call statistics never
        Connect Time = 1384, Charged Units = 0,
        Successful Calls = 1, Failed Calls = 0, Incomplete Calls = 0
        Accepted Calls = 0, Refused Calls = 0,
        Last Disconnect Cause is "10  ",
        Last Disconnect Text is "normal call clearing (16)",
        Last Setup Time = 41369385.
        Last Disconnect Time = 41371110.
Matched: 7004   Digits: 5
Target:
!---------------------------------------------------
MNPR001#sh dial-peer voice summary | inc 7004
20193  pots  up   up             7004$              0                           50/0/104
20194  pots  up   up             64367004$          0                           50/0/104
!----------------------------------------------------
MNPR001#show ver
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(20)T4, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 01-Sep-09 16:07 by prod_rel_team

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

MNPR001 uptime is 2 weeks, 5 days, 14 hours, 27 minutes
System returned to ROM by power-on
System restarted at 17:00:35 WST Thu Dec 13 2012
System image file is "flash:c2800nm-spservicesk9-mz.124-20.T4.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 2851 (revision 53.51) with 247808K/14336K bytes of memory.
Processor board ID
2 Gigabit Ethernet interfaces
21 Serial interfaces
1 terminal line
1 Channelized/Clear E1/PRI port
2 Voice FXO interfaces
2 Voice E & M interfaces
1 cisco service engine(s)
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
515088K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102
!----------------------------------------------------

Everyone's tags (4)
3 REPLIES 3
Highlighted
Hall of Fame Master

CME 2851 - Dropping calls on primary DN when shared line is answ

Update IOS and check again.

Highlighted
Beginner

Re: CME 2851 - Dropping calls on primary DN when shared line is

Update to symptoms....

I cut the number or users assigned to the shared line down to 2 from 7 and rebooted the router, now the symptoms seem to have changed. Now when a call comes in on the shared line, the operator is unable to transfer the call.

Do you think it could be a DSP allocation issue?

Does this change your recommendation to perform an upgrade? Anyways I have an upgrade scheduled for next week so then we should know.

Thanks

DGW

Highlighted
Beginner

CME 2851 - Dropping calls on primary DN when shared line is answ

IOS upgrade had no effect.

After further testing it appears that when there are more than 1 phone assigned the shared line button, the symptoms appear.

Any input regarding this would be appreciated.

CreatePlease to create content