02-19-2014 04:29 AM - edited 03-18-2019 11:20 AM
hi all ,
i have already configured CDR file accounting on my GW Cisco 2811 using FTP server , i can get the file record but i uploaded a template to customize the output attributes , but it's not working.
Notes:
1. Cisco 2811 , with IOS c2800nm-ipvoice_ivs-mz.151-2.T1_2.bin
2. Router configuration :
#gw-accounting file
#acct-template cdr
#primary ftp 192.168.1.24/CDR username cisco password cisco
#maximum buffer-size 40
#maximum retry-count 3
#maximum cdrflush-timer 1
#cdr-format compact
3.
CDR template cdr is running
url: tftp://192.168.1.4/cdr.cdr
The last load was successful.
peer-address
peer-id
peer-if-index
Totally 3 attrs defined.
4. the output before apply Template is
1392811331,565,0,1,"390FFC8C 989411E3 86FEDD53 7C448616","104","","12:00:13.123 UTC Wed Feb 19 2014","","12:00:19.033 UTC Wed Feb 19 2014","12:02:11.103 UTC Wed Feb 19 2014","10 ","normal call clearing (16)","answer",0,"",0,0,5599,895840,"104","104","","TWC","02/19/2014 12:00:13.121","104","",0,604,390FFC8C 989411E3 86FEDD53 7C448616,235,"","","",""
1392811331,566,0,1,"390FFC8C 989411E3 86FEDD53 7C448616","922823851","","12:00:16.061 UTC Wed Feb 19 2014","","12:00:19.021 UTC Wed Feb 19 2014","12:02:11.131 UTC Wed Feb 19 2014","10 ","normal call clearing (16)","originate",0,"",5599,940632,5603,896480,"104","104","922823851","TWC","02/19/2014 12:00:16.057","104","922823851",0,605,390FFC8C 989411E3 86FEDD53 7C448616,236,"","","",""
5. the output after applying Template is the same no change after applying template
why there is no change after applying template ????
02-22-2014 10:10 PM
Hi Hassan,
Detailed records have 123 entries , compact has 22 entries, while filterable are 97 which
you can specify in the custom file.
Other entries are compulsory and would still be present.
So the logic is :
If detailed is selected and custom template is being used , out of 123 you have option to
filter 97 entries.
If compact is being used you have an option to remove the ones present in the list of 97
from the 22 entries present in compact mode.
List of attributes:
These are 97 filterable attributes :
router#sh call accounting-template voice master
account-code
acom-level
backward-call-indicators
call-id
calling-party-category
charge-number
charged-units
codec-bytes
disconnect-text
early-packets
faxrelay-start-time
faxrelay-stop-time
faxrelay-max-jit-buf-depth
faxrelay-jit-buf-ovflow
faxrelay-mr-hs-mod
faxrelay-init-hs-mod
faxrelay-num-pages
faxrelay-direction
faxrelay-ecm-status
faxrelay-encap-prot
faxrelay-nsf-country-code
faxrelay-nsf-manuf-code
faxrelay-fax-success
faxrelay-tx-packets
faxrelay-rx-packets
faxrelay-pkt-conceal
gw-final-xlated-cdn
gw-final-xlated-cgn
gapfill-with-interpolation
gapfill-with-prediction
gapfill-with-redundancy
gapfill-with-silence
gk-xlated-cdn
gk-xlated-cgn
gw-rxd-cdn
gw-rxd-cgn
gw-collected-cdn
h323-call-origin
h323-call-type
h323-connect-time
h323-disconnect-cause
h323-disconnect-time
h323-gw-id
h323-remote-address
h323-setup-time
h323-voice-quality
hiwater-playout-delay
info-type
incoming-area
in-carrier-id
in-intrfc-desc
in-trunkgroup-label
internal-error-code
isup-carrier-id
late-packets
logical-if-index
lost-packets
lowater-playout-delay
max-bit-rate
noise-level
ontime-rv-playout
originating-line-info
outgoing-area
out-carrier-id
out-intrfc-desc
out-trunkgroup-label
peer-address
peer-id
peer-if-index
redirected-station
receive-delay
remote-udp-port
remote-media-address
remote-media-udp-port
round-trip-delay
service-descriptor
session-protocol
subscriber
transmission-medium-req
tx-duration
vad-enable
voice-tx-duration
voice-feature
feature-operation
feature-op-time
feature-op-status
feature-id
feature-vsa
dsp-id
release-source
alert-timepoint
ip-phone-info
ip-pbx-mode
in-lpcor-group
out-lpcor-group
fac-digits
fac-status
Totally 97 attributes are filterable.
So according to your configuration, you have used compact and you have defined 3 attributes.
So total attributes will be 25 that you will see in your excel sheet.
Thanks & Regards,
Mudit Mathur
02-25-2014 02:50 AM
Thanks for your interest
i understand now
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide