10-20-2014 01:21 AM - edited 03-17-2019 12:36 AM
Hi,
I trying to integrate with Alcatel PBX over Qsig as I don't have SIP license in Alcatel. My question is callback feature supported over qsig to alcatel pbx?
I am getting this message from the phone "callback cannot be activated on xxxx"
Regards,
10-21-2014 12:00 AM
Маке а trace for callback attempt.on Cisco or Alcatel side.
10-21-2014 12:52 AM
10-21-2014 01:57 AM
This is a CCNR request from Alcatel
| (762889:000015) 1243: Send_IO1 (link-nbr=1, sapi=0, tei=0) :
| long: 159 desti: 0 source: 15 cryst: 1 cpl: 13 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : SETUP [05] Call ref : 00 1b
| SENDING COMPLETE
|______________________________________________________________________________
|
| IE:[04] BEARER_CAPABILITY (l=2) a8 80
| IE:[18] CHANNEL (l=1) a8 -> T2 : No B channel
| IE:[1c] FACILITY (l=60)
| [9f] Discriminator of supplementary service applications
| [aa] NFE (l=6):
| [80] Source Entity (l=1) End_PTNX
| [82] Destination Entity (l=1) End_PTNX
| [a1] INVOKE (l=38):
| Invoke Ident. : 2efb (12027)
| OP: 001b (27)
| [30] Sequence (l=29)
| [a0] Context specific (l=7)
| [80] Context specific (l=5) 34 35 35 31 31
| [80] Context specific (l=5) 34 35 30 37 35
| [40] Application (l=5) 04 03 80 90 a3
| [8c] Context specific (l=1) ff
| [8d] Context specific (l=1) ff
This is an answer from Cisco router.
______________________________________________________________________________
| (762890:000020) Concatenated-Physical-Event :
| long: 22 desti: 0 source: 0 cryst: 1 cpl: 13 us: 0 term: 0 type a5
| tei: 0 >>>> message received : REL COMP [5a] Call ref : 80 1b
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 80 e4 -> [e4] INVALID INFORMATION ELEMENT CONTENTS
|______________________________________________________________________________
Looks like it is not configured properly for QSIG as it does not "understand"
FACILITY request.
11-05-2014 04:51 AM
I got these details.
Cisco is sending
Oct 30 09:29:02.040: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0011
Sending Complete
Bearer Capability i = 0xA880
Standard = ISO/IEC
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = Packet - not specified
Channel ID i = 0xAC
Exclusive, Channel 52
Facility i = 0x91AA06800100820100A129020200B106042B0C0928301DA0078005343534373380053435353131400504038090A38C01008D01FF
Calling Party Number i = 0x0081, '45473'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '45511'
Plan:Unknown, Type:Unknown
and Alcatel send
Oct 30 09:29:02.076: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8011
Channel ID i = 0xA8
Exclusive, Channel 64
CCM is sending the Invalid information element, because Alcatel sends A8 instead of AC.
11-05-2014 05:57 AM
First, which call you try to investigate?
Your first trace shows a CCNR attempt when calling from Alcatel to Cisoc and tje latest one shows a call from Cisco to Alcatel.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: