cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
1851
Views
15
Helpful
10
Replies
Tommy .
Beginner

CUCM 10 DTMF not working when outgoing call using FAC

Hi all ,

I have Installed CUCM 10  in BE6K , but when I settin route pattern for outgoing call , when using FAC , any call that need DTMF , the DTMF is not responding , but when outgoing call not using FAC , DTMF working perfectly fine .

voice gateway using MGCP with FXO.  I have tested all ports FXO but working fine when used without FAC , when using FAC DTMF not responding.

CUCM version 10.0.1.10000-24

any help please ?

 

 

Regards,

Tommy

 

2 ACCEPTED SOLUTIONS

Accepted Solutions
Rob Huffman
Hall of Fame Community Legend

Hi Tommy,

 

It looks like you may be hitting this bug;

 

DTMF failure when FAC/CMC is enabled on route pattern
CSCun34848
 
Symptom:
When FAC/CMC is enabled at the route pattern level, DTMF will not work.

You get the following error after a digit is pressed by the IP Phone.

01509471.001 |22:05:21.251 |AppInfo |StationInit: (0000084) KeypadButton kpButton=8.
01509478.001 |22:05:21.251 |AppInfo |FacCmcManager::wait_SsUserInfoInd - route by party failed! ss=18210643

Conditions:
FAC/CMC should be enabled at the route pattern level

Workaround:
Do not use FAC/CMC
 
Last Modified:
Apr 4,2014
Status:
Fixed
Severity:
2 Severe
Product:
Cisco Unified Communications Manager (CallManager)
Support Cases:
4
 
 
Cheers!
Rob

View solution in original post

yusuf habibi
Beginner

yeahh i have problem too...DTMF not working if using FAC...very weird CUCM 10 buggie

Hi tommy, did u solve it ?

 

solving after upgrade patch version smiley

10.5(0.98000.520)
10.5(0.98000.312)
10.0(1.11006.1)
Regards, Habibi

View solution in original post

10 REPLIES 10
Jaime Valencia
Hall of Fame Cisco Employee

FAC is before you even try to route the call to any GW, it doesn't matter what you use to make the calls.

What phone are you using??

Is it directly registered to CUCM??

What's the call flow??

If you dial the FAC, and press # does it route the call???

HTH

java

if this helps, please rate

Phone type I'm using is 6941, CIPC, 7912

all phone directly registered to CUCM

call flow is

call 9XXXX --> enter FAC XXX --> call connected , BUT if the connected call have IVR , and must choose for any menu , when input digits , there is no respond at all . i have tried many call that have IVR but none working.

if call flow without FAC it is working fine .

 

Regards

Tommy.

Can you describe the full call flow including what devices it's going through?  You mention above an MGCP FXO port being part of the call flow.

 

6921 sccp --> route pattern --> call 9.XXX --> enter FAC XXX --> Route List (RL1) --> Route Group (RG1) in this route group i specify only to one FXO port --> Voice Gateway 2911 (MGCP Router with FXO)--> PSTN

 

Regards,

 

Tommy

 

Could you please use the command debug mgcp packets and check whether you receiving any digit on the router when pressed for IVR menu.

 

Also check the DTMF config on the router and whether MRGL is applied to the MGCP router.

Please provide details if possible traces.

 

Rob Huffman
Hall of Fame Community Legend

Hi Tommy,

 

It looks like you may be hitting this bug;

 

DTMF failure when FAC/CMC is enabled on route pattern
CSCun34848
 
Symptom:
When FAC/CMC is enabled at the route pattern level, DTMF will not work.

You get the following error after a digit is pressed by the IP Phone.

01509471.001 |22:05:21.251 |AppInfo |StationInit: (0000084) KeypadButton kpButton=8.
01509478.001 |22:05:21.251 |AppInfo |FacCmcManager::wait_SsUserInfoInd - route by party failed! ss=18210643

Conditions:
FAC/CMC should be enabled at the route pattern level

Workaround:
Do not use FAC/CMC
 
Last Modified:
Apr 4,2014
Status:
Fixed
Severity:
2 Severe
Product:
Cisco Unified Communications Manager (CallManager)
Support Cases:
4
 
 
Cheers!
Rob

View solution in original post

Is CUCM cluster need to be restarted after install the device pack?

Rob Huffman
Hall of Fame Community Legend

Hi Kelvin,

 

I don't believe that it's a Device Pack that needs to be installed to fix this issue but rather a full CUCM SR/Patch....

 

Known Fixed Releases:
(4)
10.5(0.98000.520)
10.5(0.98000.312)
10.0(1.11006.1)
10.5(1.10000.7)

 

It shows this bug as "fixed in" CUCM 10.0(1)SU2 smiley

From;

http://www.cisco.com/web/software/282074295/114809/cucm-readme-1001su2.pdf

 

Cheers!

Rob 

Yea, I have upgraded to the CUCM 10.0(1)SU2 and the problem solve :D

yusuf habibi
Beginner

yeahh i have problem too...DTMF not working if using FAC...very weird CUCM 10 buggie

Hi tommy, did u solve it ?

 

solving after upgrade patch version smiley

10.5(0.98000.520)
10.5(0.98000.312)
10.0(1.11006.1)
Regards, Habibi

View solution in original post

Create
Recognize Your Peers
Content for Community-Ad