cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

971
Views
0
Helpful
10
Replies
Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Dear Team,

My system use CUCM 9.1. Includes sccp phone 8945, sip phone 8961.

I dial from sccp phone 8945 to pstn phone, i wait about 10 second to hear ringing signal, it 's ok.

But when i dial from sip phone 8961 to pstn phone, i wait about 26 second, it 's too a long time.

Please help me, how to set parameter on CUCM to reduce dial time of sip phone 8961.

Thanks.

10 REPLIES 10
Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi,

does this happen for all route patterns, or just for international ?

regards

Anas

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi Anas,

Happen for all route patterns.

Thanks.

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

HI,

what is your gateway, h323 or sip ?

try to use # at the end of the call, it will speed the call beacuse it is a SIP.

HTH

Anas

please rate if it is helpful

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi Anas,

Voice gateway is h323. when i dial from sccp phone 8945, it ok,

But dial from sip phone 8961, it 's too slow to make a call.

Do you have other solution, how to set sip parameter on CUCM?

Thanks.

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi Anas,

I just see link on forrum.

https://supportforums.cisco.com/message/3867429?referring_site=bss&channel=bdp#3867429

Please give me advises,

Thanks.

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi Nam,

they are talking about firmware update. try to update to the latest one if possible.

for timer you can go to service parameters, choose the call manager service to find the T302  parameter to minimize the time

HTH

Anas

please rate if it is helpful

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi Anas,

I see a lot of parameter T302 on cucm.

You can help me which of detail of name T302?

Thanks.

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi Nam,

change the value to 4000 and test. My recommendation is to upgrade firmware.

kindly find the below description for T302.

This parameter specifies an interdigit timer for sending the SETUP ACK message.

The timer restarts each time Cisco CallManager receives a digit. When this timer expires,

Cisco CallManager routes the dialed digits. For exact timer definitions,

refer to the Q.931 specification. 

   This is a required field. 

   Default:  15000 

   Minimum:  3000 

   Maximum:  75000 

   Unit: msec 

HTH

Anas

please don't forget to rate the helpful posts

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi Anas,

I just disscus my team, firmware 8961 was updated with lastest version (8961.9-3-2-10).

Tomorrow, i will change T302 to 4000, and test.

How about set timeout digit on voice gateway, or set sip dial rule on cucm? need or no need?

Thanks.

Highlighted

[CUCM 9.1] sip phone 8961 dial to pstn a long time

Hi ,

we are having the exact issue with CUCM 9.1 with SIP phones(6921 ,9951,3905 ) ,IDD dialing

any ideas ?

thanks

Purna

CreatePlease to create content
Content for Community-Ad
Future of Work Virtual Summit Day 5

Cisco COVID-19 Survey