02-23-2019 12:28 AM
Hi everybody
I have integrated an ISR 4331 with FXS ports connected to CUCM 11.5 via SIP .The issue i am facing is When i make an call from CUCM endpoint to the FXS extension i am not getting ringback tone in CUCM end ,but the FXS extension is ringing and when answered it has one way audio path , When i try to dial from FXS port to an ip phone in CUCM end the call is not getting established .Have attached the Show run output from ISR 4331 ,kindly give your valuable guidance to overcome this issue.
02-23-2019 11:09 PM
The ISR 4331 config which has the issue
MCIT-VGW-1#show run
Building configuration...
Current configuration : 5556 bytes
!
! Last configuration change at 11:06:13 utc Sat Feb 23 2019 by mcitadmin
! NVRAM config last updated at 10:17:02 utc Sat Feb 23 2019 by mcitadmin
!
version 16.6
service timestamps debug datetime msec
service timestamps log datetime msec
platform qfp utilization monitor load 80
no platform punt-keepalive disable-kernel-core
!
hostname MCIT-VGW-1
!
boot-start-marker
boot-end-marker
!
!
vrf definition Mgmt-intf
!
address-family ipv4
exit-address-family
!
address-family ipv6
exit-address-family
!
!
no aaa new-model
clock timezone utc 4 30
!
!
subscriber templating
!
!
multilink bundle-name authenticated
!
voice call send-alert
!
voice service voip
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
bind control source-interface GigabitEthernet0/0/0
bind media source-interface GigabitEthernet0/0/0
!
!
voice class uri 2 sip
host ipv4:172.14.14.10
host ipv4:172.14.14.13
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g722-64
!
!
!
voice class server-group 1
ipv4 172.14.14.10 preference 1
ipv4 172.14.14.13 preference 2
!
voice class sip-options-keepalive 1
!
voice-card 0/1
no watchdog
!
voice-card 0/2
no watchdog
!
voice-card 0/4
no watchdog
!
license udi pid ISR4331/K9 sn FDO223109CZ
diagnostic bootup level minimal
spanning-tree extend system-id
!
!
!
username mcitadmin privilege 15 password 0 Mc!t@k@bul
!
redundancy
mode none
!
!
interface GigabitEthernet0/0/0
ip address 172.14.14.20 255.255.255.0
negotiation auto
!
interface GigabitEthernet0/0/1
no ip address
negotiation auto
!
interface GigabitEthernet0/0/2
no ip address
negotiation auto
!
interface Service-Engine0/1/0
no ip address
!
interface Service-Engine0/2/0
no ip address
!
interface Service-Engine0/4/0
no ip address
!
interface GigabitEthernet0
vrf forwarding Mgmt-intf
no ip address
negotiation auto
!
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http client source-interface GigabitEthernet0/0/0
ip route 0.0.0.0 0.0.0.0 172.14.14.3
!
control-plane
!
!
voice-port 0/1/0
ring frequency 50
ring cadence pattern01
!
voice-port 0/1/1
ring frequency 50
ring cadence pattern01
!
voice-port 0/1/2
!
voice-port 0/1/3
!
voice-port 0/2/0
!
voice-port 0/2/1
!
voice-port 0/2/2
!
voice-port 0/2/3
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
dial-peer voice 1901 pots
destination-pattern 1901
port 0/1/0
!
dial-peer voice 1902 pots
destination-pattern 1902
port 0/1/1
!
dial-peer voice 2 voip
description incomming calls from CUCM
session protocol sipv2
incoming uri via 2
voice-class codec 1
dtmf-relay sip-kpml rtp-nte
no vad
!
dial-peer voice 1801 voip
description outgoing calls to CUCM
destination-pattern 1801
session protocol sipv2
session server-group 1
voice-class codec 1
dtmf-relay sip-kpml rtp-nte
no vad
!
!
!
line con 0
login local
transport input none
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password Mc!t@k@bul
login local
transport input all
!
ntp server 172.12.12.21
wsma agent exec
!
wsma agent config
!
wsma agent filesys
!
wsma agent notify
!
!
end
MCIT-VGW-1#show version
Cisco IOS XE Software, Version 16.06.03
Cisco IOS Software [Everest], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.6.3, RELEASE SOFTWARE (fc8)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Wed 28-Feb-18 23:54 by mcpre
ROM: IOS-XE ROMMON
MCIT-VGW-1 uptime is 2 days, 19 hours, 3 minutes
Uptime for this control processor is 2 days, 19 hours, 6 minutes
System returned to ROM by Reload Command
System restarted at 16:43:56 utc Wed Feb 20 2019
System image file is "bootflash:isr4300-universalk9.16.06.03.SPA.bin"
Last reload reason: Reload Command
Suite License Information for Module:'esg'
--------------------------------------------------------------------------------
Suite Suite Current Type Suite Next reboot
--------------------------------------------------------------------------------
FoundationSuiteK9 None None None
securityk9
appxk9
AdvUCSuiteK9 None None None
uck9
cme-srst
cube
Technology Package License Information:
-----------------------------------------------------------------
Technology Technology-package Technology-package
--More-- Current Type Next reboot
------------------------------------------------------------------
appxk9 None None None
uck9 uck9 Permanent uck9
securityk9 None None None
ipbase ipbasek9 Permanent ipbasek9
cisco ISR4331/K9 (1RU) processor with 1796073K/6147K bytes of memory.
Processor board ID FDO2232A2FP
3 Gigabit Ethernet interfaces
8 Voice FXS interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
3207167K bytes of flash memory at bootflash:.
0K bytes of WebUI ODM Files at webui:.
Configuration register is 0x2102
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide