CUCME 8.6 archive tar /xtract command

[me.saadiqbal]

Hi There,

I am trying to install a fresh CUCME/CME on 2901 router , the version of cme is 8.6

I have the cme-buddle on the root of the tftp installed on my PC.

Cisco Docs makes it so simple ;

archive tar /xtract                source-url               flash:/file-url

Could you please give us an example of the source-url part .

I am getting the error

%Error opening tftp://.......

[chrysostomos1980]

Hi

archive tar /xtract tftp://tftp-ip-address/package-name.tar flash:

Regards

cc

[me.saadiqbal]

Hi Chrysostomos1980,

what do you mean by package name?

I have tried this ,

archive tar /xtract tftp://172.16.27.5/cme-151-4Mv1.tar flash:

this is a full bundle, Is there any mistakes in the one above?

[Ayodeji Okanlawon]

What tftp server are you using? Is the file present in the root directory of your tftp server? If you get error opening the file, its most likely you have not setup your tftp server properly

Please rate all useful posts

"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson

[me.saadiqbal]

I am using Solar Winds, and Yes I have put the cme zip file on the tftp root?

I have started and restarted the tftp server.!!!

I have also rechecked the command, the syntax is also correct.

I see that the problem is with the tftp server, but not able to isoloate the problem,

I have confirmed that the my PC's firewall is off also..

[chrysostomos1980 · Accepted solution]

Hi

cme-151-4Mv1.tar is the general folder

You have to issue the above command for each file that is in this folder

Example1:

open the cme-151-4Mv1.tar.There you will find many other folders

moh.tar file example

Then the command will be

archive tar /xtract tftp://10.10.10.1/moh.tar flash:

Example2:

May you  find the below folder

7970-7971-sip.8-4-2S.tar

so the command will be

archive tar /xtract tftp://10.10.10.1/7970-7971-sip.8-4-2S.tar flash:

If some files are not .tar format and you want to convert it to .tar format then you can use this link or something else for the conversion

http://www.convertfiles.com/

Regards

cc

[me.saadiqbal]

thanks chrysostomos1980

I will update you once I tried that,

[me.saadiqbal]

thanks

chrysostomos1980

        that worked!!!!

[chrysostomos1980]

Hi Mohammed

Great

Note:

After to xtract the files into flash and the files will be in directory (below is an example) then Pls remember to use this format for the tftp-server

tftp-server flash:/MEDIA/music-on-hold.au alias music-on-hold.au

tftp-server flash:/RINGTONES/Analog1.raw alias Analog1.raw

tftp-server flash:/RINGTONES/AreYouThere.raw alias AreYouThere.raw

In flash will like that:

Example in flash:

MEDIA

MEDIA/music-on-hold.au

RINGTONES

RINGTONES/Analog1.raw

RINGTONES/AreYouThere.raw

[zidjali2007]

Dear ,

Could you list to me the steps if I want to upgrade my  telephony-service from 10.5 to 11.

If you give the link to download the related IOS or cme version It will more better. I want to do this upgrade for CISCO router 2901 IOS Version 15.5(1)T,.

Regards,

[Mohammed al Baqari]

You need to have CCO account download the tar file from cisco.com

[Rajan]

here is the link to download tar file and as mentioned here you need a cisco CCO account to download from this page:

https://software.cisco.com/download/release.html?mdfid=277641082&softwareid=282786567&release=11.6&relind=AVAILABLE&rellifecycle=&reltype=latest

You need to check the compatibility matrix in the below link. and download the corresponding IOS versions:

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/requirements/guide/33matrix.html

Link to download IOS:

https://software.cisco.com/download/release.html?mdfid=282774223&flowid=7438&softwareid=280805680&release=15.5.3M5&relind=AVAILABLE&rellifecycle=MD&reltype=latest

HTH

Rajan

Pls rate all useful posts