cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1187
Views
0
Helpful
6
Replies

CUCME & CUE (ISM) integration (AA not functioning)

Hi,

I have a client with ISR 2901 . A cucme (Software Version  15.2(3)T1 / CME 9.0  ) with CUE (Cisco Unity Express - Administration Version 8.6.1)

is configured.

The following is cucme configuration for CUE

"Interfaces configuration"

interface ISM0/0

ip unnumbered GigabitEthernet0/1.10

service-module ip address 172.16.10.3 255.255.255.0

!Application: CUE Running on ISM

service-module ip default-gateway 172.16.10.1

!

interface GigabitEthernet0/1

description "Connected to BOM-SW1 Gig0/24"

no ip address

no ip redirects

no ip proxy-arp

ip virtual-reassembly in

duplex auto

speed auto

!

interface GigabitEthernet0/1.10

description "Voice Sub Interface"

encapsulation dot1Q 10

ip address 172.16.10.1 255.255.255.0

!

ip route 172.16.10.3 255.255.255.255 ISM0/0

Dial-Peer-Config for Unity

dial-peer voice 800 voip

description <Unity#555autoattendent>

destination-pattern 555

session target ipv4:172.16.10.3

voice-class codec 1 

dtmf-relay h245-alphanumeric

ip qos dscp cs3 signaling

no vad

!

dial-peer voice 808 voip

description (autoattendentUnity#555-sip)

destination-pattern 555

session protocol sipv2

session target ipv4:172.16.10.3

dtmf-relay sip-notify

codec g711ulaw

no vad

!

dial-peer voice 222 voip

description <ICM-CUE>

destination-pattern 554

session target ipv4:172.16.10.1

voice-class codec 1 

dtmf-relay h245-alphanumeric

ip qos dscp cs3 signaling

no vad

!

Voice-Ports Configuration

voice-port 0/1/0

trunk-group BOM-OUT

supervisory disconnect dualtone mid-call

timeouts interdigit 3

timeouts call-disconnect 1

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 555

description <Ph.No. 013390>

caller-id enable

!

voice-port 0/1/1

trunk-group BOM-OUT

supervisory disconnect dualtone mid-call

cptone GB

timeouts interdigit 4

          timeouts call-disconnect 1

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 555

impedance complex2

description <Ph.No. 030191>

bearer-cap Speech

caller-id enable

!

Unity Express Configuration

groupname Administrators member administrator

groupname Broadcasters privilege broadcast

username Receiptionist phonenumber "101"

restriction msg-notification create

restriction msg-notification min-digits 1

restriction msg-notification max-digits 30

restriction msg-notification dial-string preference 1 pattern * allowed

calendar biz-schedule systemschedule

closed day 1 from 00:00 to 24:00

open day 2 from 08:00 to 17:00

open day 3 from 08:00 to 17:00

open day 4 from 08:00 to 17:00

open day 5 from 08:00 to 17:00

open day 6 from 08:00 to 17:00

closed day 7 from 00:00 to 24:00

end schedule

ccn application autoattendant aa

description "autoattendant"

enabled

maxsessions 2

script "welcome.aef"

end application

ccn application ciscomwiapplication aa

description "ciscomwiapplication"

enabled

maxsessions 10

script "setmwi.aef"

parameter "CallControlGroupID" "0"

parameter "strMWI_OFF_DN" "8001"

parameter "strMWI_ON_DN" "8000"

end application

ccn application msgnotification aa

description "msgnotification"

enabled

maxsessions 10

script "msgnotify.aef"

parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"

parameter "DelayBeforeSendDTMF" "1"

end application

ccn application promptmgmt aa

description "promptmgmt"

enabled

maxsessions 1

script "promptmgmt.aef"

parameter "appManagementScript" ""

end application

ccn application voicemail aa

description "voicemail"

enabled

maxsessions 10

script "voicebrowser.aef"

parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"

parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"

end application

ccn engine

end engine

ccn reporting historical

database local

description "se-172-16-10-3"

end reporting

ccn subsystem email

end subsystem

ccn subsystem fax

end subsystem

ccn subsystem sip

gateway address "172.16.10.1"

end subsystem

ccn trigger http urlname msgnotifytrg

application "msgnotification"

enabled

maxsessions 2

end trigger

ccn trigger http urlname mwiapp

application "ciscomwiapplication"

enabled

maxsessions 1

end trigger

ccn trigger sip phonenumber 555

application "autoattendant"

enabled

locale "en_US"

maxsessions 2

end trigger

ccn trigger sip phonenumber 554

application "voicemail"

enabled

maxsessions 4

end trigger

service phone-authentication

end phone-authentication

service voiceview

enable

end voiceview

voicemail broadcast recording time 300

voicemail default messagesize 240

voicemail notification restriction msg-notification

voicemail operator telephone 101


!

The Call from outside is hitting on Voice Port 0/1/0 or 1 and hitting Dial-peers for CUE :"PLAR555".

But welcome message is not getting played.

Please need support for this case.

Thanks


)

)

6 Replies 6

mahmoodmkl
Level 7
Level 7

Hi.

I think u only need 1 dail-peer for AA and u r missing the below from the first dial-peer.

session protocol sipv2

Thanks

Thanks for your support.

I have included this command but still same result.

Do you think I need any more configuration on CUE!!

Thanks

Hi,

Thanks for this.

I have follow it. But issue is same.

it is not working.

Do u think we need to make any specific configuration change on CUE?

Thanks

I have found that if i call from local extension to AA # 555. the dp 800 or 808 is matched but only phone show 555 aa line busy

status.

what its mean?

The issue is resolved.

On unity i had to give command to activate license for mailbox.

This enable license for aa .

Thanks for your support.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: