08-18-2013 07:09 AM - edited 03-16-2019 06:55 PM
I am not able to access cue gui.
I've already configured it with appropiat settings.
i also tried this:
1. In CUE config mode - "crypto key generate rsa label gui modulus 1024"
2. reload
4. In CUE config mode - "web session security keyLabel gui"
3. enable TLS 1.0 in IE and Firefox
4. In browser address bar enter: https:// <cue ip> OR http://<cue ip>:443
didnt work
I'm using IE version 10
I configured CUE wit ip address it's reachable from all other sites.
But its not accessible from my local machine.
did i forgot something?
Solved! Go to Solution.
08-19-2013 04:46 AM
Hi,
Add route as below
route add 10.10.115.2 mask 255.255.255.0
And then try to ping
08-18-2013 09:32 AM
Make sure you have the following:
!
ip http server
no ip http secure-server
ip http path flash:/gui
!
in the telephony-service
web admin system name ....
dn-webedit
08-19-2013 03:57 AM
is it neccasry that i have to configure cme first before enabling cue gui.
I didnt knew that cue had to do something with cme.
I thougt it was independend
08-19-2013 04:11 AM
Hi,
From where you are trying to access youu CUE web page?
Are you able to ping that CUE IP address from the same device (from your PC / laptop) from where you are trying to access web page?
If you are not able to ping then add persistent route in your cmd prompt and try to access.
08-19-2013 04:44 AM
Hi,
I see the problem i am not able to ping from my local laptop machine.
based on my site c router cue configuration
interface Service-Engine0/0
ip unnumbered Loopback1
service-module ip address 10.10.115.2 255.255.255.0
service-module ip default-gateway 10.10.115.1
i added this route in cmd.
route add 10.10.115.2 mask 255.255.255.0 10.10.115.1 -p
will this help because still not reachable
08-19-2013 04:44 AM
time out while pinging
08-19-2013 04:46 AM
Hi,
Add route as below
route add 10.10.115.2 mask 255.255.255.0
And then try to ping
08-19-2013 05:08 AM
Still no success, i will show you my routeprint
IPv4 routetabel
===========================================================================
Actieve routes:
Netwerkadres Netmasker Gateway Interface Metric
10.10.210.0 255.255.255.0 On-link 10.10.210.15 281
10.10.210.15 255.255.255.255 On-link 10.10.210.15 281
10.10.210.255 255.255.255.255 On-link 10.10.210.15 281
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.50.0 255.255.255.0 On-link 192.168.50.103 281
192.168.50.103 255.255.255.255 On-link 192.168.50.103 281
192.168.50.255 255.255.255.255 On-link 192.168.50.103 281
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 10.10.210.15 281
224.0.0.0 240.0.0.0 On-link 192.168.50.103 281
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 10.10.210.15 281
255.255.255.255 255.255.255.255 On-link 192.168.50.103 281
===========================================================================
Permanente routes:
Netwerkadres Netmask Gateway-adres Metric
10.10.115.2 255.255.255.0 10.10.210.15 1
===========================================================================
pfff i am lost
08-19-2013 05:17 AM
Do you have UCCX installed?
If yes then you can open CUE from uccx.
You are not able to open from your latptop is just because of recheability problem. Try to add route and verify the same. It should work.
08-19-2013 05:17 AM
Hi nishant,
It worked!
Your the men....
i disabled my LAN connection, re-enabled it.
Now it works fine i can ping and reach my CUE GUI
awesome!
Thank you very much!
08-19-2013 05:18 AM
Great!!!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide