cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
837
Views
3
Helpful
14
Replies

dialing for pstn local cme number is ringing

is_mail123
Level 1
Level 1

hi,

we have a problem we we dial the pstn outside number that start with 212.... the call will be send to the local ipphone in cme environment.

how to say the cme system to collect all the digit and select the appropriate dial-peer for the calling.image you unhook the cardle and intent to call 2123456 (a landline pstn) ,as soon as you hit the 212 immediately goes to the cme local ipphone.

Local cme ipphone extension range is 2xx

ephone-dn 23 dual

number 212

!

!

!

dial-peer voice 55 pots

destination-pattern .T

voice-port 0/1/1

above is the snapshot . need help bros

14 Replies 14

Leonardo Santana
Spotlight
Spotlight

Hello because the 212 is more specific than .T, configure the pstn dial-peer this way:

dial-peer voice 55 pots

destination-pattern 9T

voice-port 0/1/1

Documentation:

http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml

Rate this if helps you!

Thanks!

Regards
Leonardo Santana

*** Rate All Helpful Responses***

acampbell
VIP Alumni
VIP Alumni

Hi,

You NEED to change the DNs that start with or are 212

You can not expect the call to route outside when the number is matched inside.

A simple answer would be to use an access code for the PSTN usually a "9"

So 9.2123456 will route to PSTN the 9 would be dropped if yiou used a dial peer

dial-peer voice 55 pots

destination-pattern 9T

voice-port 0/1/1

HTH

alex

Regards, Alex. Please rate useful posts.

we cannot use any code before as it is a client requirment  ...i changed the voip dial-peer to

destina-pattern 212....       i mean there might be a way to tell the system to collect the digit first and match the exact dial per  instead  just going to dial what the first match is

can you change the DNs of the ip phones? like a code site?

Regards
Leonardo Santana

*** Rate All Helpful Responses***

no

leonardotadeu  we cannot make any changes in dn's

Do you have to dial 212 area code as 10 digits?

I belive NY 212 area code requires 11 digit dialing, i.e 1 +212, is the goal to prefix 1 somewhere along the path?

Chris

and also i can call other landline without any problem like 211...  , 214....,

for 212.... i cannot directly goes to 212 ipphone.

I understand, but why are you attemting to dial 212 area code starting with 2?  In order to dial within NY area you need to dial 11 digits, i.e. 1 212 555 1234, so you dial-peer to PSTN should be destination-pattern 1[2-9]..[2-9]...... or

1212[2-9]...... if you need explicit match.

Chris

i am not in us

My appologies, I made assumptions.

SO, then you have 2 options only which have already been described:

1. Introduce off-net access code to ensure overlaps do not exist

2. Change DNs to avaoid overlaps

HTH,

Chris

that is not to be done ,if so client will remark us.i was search on net.

how to to put interdigit timeout in cme iipphone might be with this technique we can delay the digit collection and send full digit string like did and help cme to select the dial-peer

Well, you are out of options then.

Interdigit timeout would not fix your issue as DNs are immediate match, your only other option would be to implement COR lists and block access to this DN from other DNs, which I doubt is what your want.

Bad design == future consequences

Chris

Take a look on this doc to understand the dial-peer matching:

http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml

When a voice call enters the network, the router collects digits as follows:

1. The originating router collects dialed digits until it matches an outbound dial peer. (MATCHES THE MORE SPECIFIC)

2. The router immediately places the call and forwards the associated dial string.

3. The router collects no additional dialed digits.

Like Cris said the interdigit timeout will not fix your problem

Regards

Regards
Leonardo Santana

*** Rate All Helpful Responses***

I agree with Chris, or review your dial-plan with your customer.

Regards
Leonardo Santana

*** Rate All Helpful Responses***
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: