cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
666
Views
0
Helpful
7
Replies
Highlighted
Beginner

Drop Incoming Call Cisco IOS H323

Hi,

When i have Incoming Call from Externel, the Gateway (2811) dropped then make long busy tone.

*Mar 11 14:49:51.552: ISDN BR0/1/1 Q931: RX <- SETUP pd = 8  callref = 0x23
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech 
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0x89
                Exclusive, B1
        Calling Party Number i = 0x2181, '0661263920'
                Plan:ISDN, Type:National
        Called Party Number i = 0x81, '9731'
                Plan:ISDN, Type:Unknown
        High Layer Compat i = 0x9181
*Mar 11 14:49:51.560: %CALL_CONTROL-6-NUMBERING_TYPE_NO_MATCH: The called number numbering type did not matchThe event for the callid 100 is being discarded.

*Mar 11 14:49:51.564: ISDN BR0/1/1 Q931: TX -> CALL_PROC pd = 8  callref = 0xA3
        Channel ID i = 0x89
                Exclusive, B1
*Mar 11 14:49:52.564: ISDN BR0/1/1 Q931: TX -> CALL_PROC pd = 8  callref = 0xA3
        Channel ID i = 0x89
                Exclusive, B1
*Mar 11 14:49:52.584: ISDN BR0/1/1 Q931: TX -> ALERTING pd = 8  callref = 0xA3
        Progress Ind i = 0x8188 - In-band info or appropriate now available
*Mar 11 14:49:53.880: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8  callref = 0x23
        Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:53.888: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8  callref = 0x23
        Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:53.896: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8  callref = 0x23
        Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:53.896: ISDN BR0/1/1 Q931: TX -> RELEASE_COMP pd = 8  callref = 0xA3
*Mar 11 14:49:54.880: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8  callref = 0x23
        Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:54.896: ISDN BR0/1/1 Q931: TX -> RELEASE_COMP pd = 8  callref = 0xA3
*Mar 11 14:49:59.572: ISDN BR0/1/1 Q931: Ux_DLRelInd: DL_REL_IND received from L2
*Mar 11 14:50:02.232: ISDN BR0/1/1 Q931: L3_ShutDown: Shutting down ISDN Layer 3

Best Regard,

7 REPLIES 7
Highlighted
Cisco Employee

The possible reason to this is that your incoming dial-

peer does not have 'numbering-type ' on it

Highlighted

Thank's for respond, i alerdy done it but still doen's work

dial-peer voice 100 voip
numbering-type national
destination-pattern 9731

modem passthrough nse codec g711ulaw
voice-class codec 100
session target ipv4:10.2.0.21
dtmf-relay h245-alphanumeric
fax rate disable
no vad

This is configuration of Interface BRI

interface BRI0/1/0
no ip address
no ip mroute-cache
no logging event link-status
isdn switch-type basic-dms100
isdn timer T310 60000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0

Highlighted

Hi,

Please try config:

dial-peer voice 1 pots
incoming called-number .
direct-inward-dial

Tanks.

MC

Highlighted

thank for replay, it's does'nt solve the problem either and i also see when debug isdn Q931 show

        Bearer Capability i = 0x9090A3
                Standard = CCITT
                Transfer Capability = 3.1kHz Audio

the call drop without long busy tone.

Highlighted

Hi,

Can you  make outgoing calls?

Can you show  all of the router config ?

Also in voice-port do you have bearer-cap Speech?

BR

MC

Highlighted

Can you try to make numbering type in call leg for called party to match the numbering type for outgoing dial peer.
Share router config. Connection details between Gateway<----> PSTN/ PBX
Highlighted

Hi, thak's all of you for respond, the operator make some test their configuration of which creates problems. it's work now