03-11-2011 06:45 AM - edited 03-16-2019 03:55 AM
Hi,
When i have Incoming Call from Externel, the Gateway (2811) dropped then make long busy tone.
*Mar 11 14:49:51.552: ISDN BR0/1/1 Q931: RX <- SETUP pd = 8 callref = 0x23
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Exclusive, B1
Calling Party Number i = 0x2181, '0661263920'
Plan:ISDN, Type:National
Called Party Number i = 0x81, '9731'
Plan:ISDN, Type:Unknown
High Layer Compat i = 0x9181
*Mar 11 14:49:51.560: %CALL_CONTROL-6-NUMBERING_TYPE_NO_MATCH: The called number numbering type did not matchThe event for the callid 100 is being discarded.
*Mar 11 14:49:51.564: ISDN BR0/1/1 Q931: TX -> CALL_PROC pd = 8 callref = 0xA3
Channel ID i = 0x89
Exclusive, B1
*Mar 11 14:49:52.564: ISDN BR0/1/1 Q931: TX -> CALL_PROC pd = 8 callref = 0xA3
Channel ID i = 0x89
Exclusive, B1
*Mar 11 14:49:52.584: ISDN BR0/1/1 Q931: TX -> ALERTING pd = 8 callref = 0xA3
Progress Ind i = 0x8188 - In-band info or appropriate now available
*Mar 11 14:49:53.880: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8 callref = 0x23
Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:53.888: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8 callref = 0x23
Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:53.896: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8 callref = 0x23
Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:53.896: ISDN BR0/1/1 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xA3
*Mar 11 14:49:54.880: ISDN BR0/1/1 Q931: RX <- RELEASE pd = 8 callref = 0x23
Cause i = 0x8090 - Normal call clearing
*Mar 11 14:49:54.896: ISDN BR0/1/1 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xA3
*Mar 11 14:49:59.572: ISDN BR0/1/1 Q931: Ux_DLRelInd: DL_REL_IND received from L2
*Mar 11 14:50:02.232: ISDN BR0/1/1 Q931: L3_ShutDown: Shutting down ISDN Layer 3
Best Regard,
03-11-2011 07:01 AM
The possible reason to this is that your incoming dial-
peer does not have 'numbering-type ' on it
03-11-2011 07:04 AM
Thank's for respond, i alerdy done it but still doen's work
dial-peer voice 100 voip
numbering-type national
destination-pattern 9731
modem passthrough nse codec g711ulaw
voice-class codec 100
session target ipv4:10.2.0.21
dtmf-relay h245-alphanumeric
fax rate disable
no vad
This is configuration of Interface BRI
interface BRI0/1/0
no ip address
no ip mroute-cache
no logging event link-status
isdn switch-type basic-dms100
isdn timer T310 60000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
03-11-2011 09:05 AM
Hi,
Please try config:
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
Tanks.
MC
03-12-2011 05:22 AM
thank for replay, it's does'nt solve the problem either and i also see when debug isdn Q931 show
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
the call drop without long busy tone.
03-12-2011 05:33 AM
Hi,
Can you make outgoing calls?
Can you show all of the router config ?
Also in voice-port do you have bearer-cap Speech?
BR
MC
03-12-2011 06:02 AM
Can you try to make numbering type in call leg for called party to match the numbering type for outgoing dial peer.
Share router config. Connection details between Gateway<----> PSTN/ PBX
03-15-2011 04:26 AM
Hi, thak's all of you for respond, the operator make some test their configuration of which creates problems. it's work now
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: