cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
936
Views
33
Helpful
19
Replies

dtmf issue on uc540

1 Accepted Solution

Accepted Solutions

Your CUE is configured for rtp-nte

ccn subsystem sip

gateway address "10.1.10.2"

dtmf-relay rtp-nte

end subsystem

ccn subsystem sip

Please change this to

conf t

ccn subsystem sip

dtmf-relay sip-notify

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts

View solution in original post

19 Replies 19

Bruno Rangel
Spotlight
Spotlight

Hi

Check if you CUE is working properly, once that is not working fron inside

Cheers
Bruno Rangel

Please remember to rate helpful  responses using the stars bellow and identify helpful or correct answers .

Cheers
Bruno Rangel
Please remember to rate helpful responses using the star bellow and identify helpful or correct answers

What do you mean by check from inside???

i have already checked its working fine....its pinging, I can open cli of cue,Gui also works fine.

I mean if it´s working from a Internal extension

mohd abdul malik wrote:

Not only i am facing this issue when i am calling from outside but also  internally therfore am guessing this issue is related to configuration

Cheers
Bruno Rangel

Please remember to rate helpful  responses using the stars bellow and identify helpful or correct answers .

Cheers
Bruno Rangel
Please remember to rate helpful responses using the star bellow and identify helpful or correct answers

nope its not working for internal extensions also.

Is my configuration alright??

Hi Abdul,

show run (From the CUE)

Regards,

Kevin

Hi kevin,

Thanks for taking interest in my issue I really appreciate your concern for other.

Ayodeji Okanlawon
VIP Alumni
VIP Alumni

Abdul,

You didnt post the dial-peers for the CUE. Do you have sip notify configured on the dial-peer pointing to CUE on the UC520?

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts

Hi Aokanlawon,

I have posted the dialpeer in my initial question, Please have a look.

Now i have also done the dtmf-relay sip notify configuration on the dial-peer voice 750 voip.

dial-peer voice 750 voip

destination-pattern 750

session protocol sipv2

session target ipv4:10.1.10.1

dtmf-relay sip-notify

codec g711ulaw

no vad

Still its not working

Bruno Rangel
Spotlight
Spotlight

Hi

You received busy tone ? Post the output of debbug voice ccapi inout.

Also try no incoming called number . in your DP

Cheers
Bruno Rangel
Please remember to rate helpful responses using the star bellow and identify helpful or correct answers

Please check the attached requested debugs.

Can you post your full sh run..What is configured on dial-peer 102?

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts

Well 102 is an incoming dial-peer.

but its taking the dial peer 750 to route the cals to cue.

Your CUE is configured for rtp-nte

ccn subsystem sip

gateway address "10.1.10.2"

dtmf-relay rtp-nte

end subsystem

ccn subsystem sip

Please change this to

conf t

ccn subsystem sip

dtmf-relay sip-notify

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: