01-19-2011 09:28 AM - edited 03-16-2019 02:57 AM
Hi all,
I have two BRI Lines on a CCME.
1-BRI 0/2/0
2- BRI 0/3/0
I have an extension 0036, if any body make International kal from 0036 extension, the call should be route through BRI-0/3/0 ...
If any body make international call from any other extension call should pass through BRI-0/2/0 ......
i did the following configuration, but sometime call is passing through BRI-0/2/0 or some time through BRI-0/3/0...
Can any body suggest, what mistake im doing !!!
!
voice translation-rule 1
rule 1 /4350048/ /7001/
rule 2 /4350052/ /7002/
rule 3 /4350059/ /7003/
rule 4 /4350072/ /7004/
!
voice translation-rule 2
rule 1 /^0036/ /44350036/
!
voice translation-rule 3
rule 1 /.*\(....\)/ /\1/
!
!
voice translation-profile NEW-BRI
translate calling 2
!
voice translation-profile NEW-BRI-Incoming
translate called 3
!
voice translation-profile PSTNIN
translate called 1
!
!
voice-card 0
no dspfarm
!
!
!
interface BRI0/2/0
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
!
interface BRI0/3/0
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
!
interface Dialer1
no ip address
!
voice-port 0/2/0
translation-profile incoming PSTNIN
!
voice-port 0/2/1
translation-profile incoming PSTNIN
!
voice-port 0/3/0
translation-profile incoming NEW-BRI-Incoming
translation-profile outgoing NEW-BRI
!
voice-port 0/3/1
translation-profile incoming NEW-BRI-Incoming
translation-profile outgoing NEW-BRI
!
!
dial-peer voice 30 pots
destination-pattern 900T
progress_ind setup enable 3
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 0/3/0
prefix 00
!
dial-peer voice 31 pots
destination-pattern 900T
progress_ind setup enable 3
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 0/2/0
prefix 00
!
Regards,
01-19-2011 09:45 AM
Hi,
From your current config you have two dial-peers with the same preference, so the choice of BRI will be RANDOM
If you want to control certain phones using certain voice ports I would use Class of Restriction, see guide http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml
If your users are well behaved you could use different access digits for each port.
Craig
01-19-2011 01:27 PM
Hi Craig,
Thanks for your reply.
Alright let me try this by tomorrow.
Wat about incoming calls ???
I need if some body from outside calls to 0036 call should come from BRI-0/3/0 & if to other extension call should come through 0/2/0 ??
Regards,
01-19-2011 07:30 PM
Incoming depends by telco, check with them.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: