cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

245
Views
0
Helpful
3
Replies
Highlighted
Beginner

Dual BRI-Lines

Hi all,

I have two BRI Lines on a CCME.

1-BRI 0/2/0

2- BRI 0/3/0

I have an extension 0036, if any body make International kal from 0036 extension, the call should be route through BRI-0/3/0 ...

If any body make international call from any other extension call should  pass through BRI-0/2/0 ......

i did the following configuration, but sometime call is passing through  BRI-0/2/0 or some time through BRI-0/3/0...

Can any body suggest, what mistake im doing !!!

!

voice translation-rule 1

rule 1 /4350048/ /7001/

rule 2 /4350052/ /7002/

rule 3 /4350059/ /7003/

rule 4 /4350072/ /7004/

!

voice translation-rule 2

rule 1 /^0036/ /44350036/

!

voice translation-rule 3

rule 1 /.*\(....\)/ /\1/

!

!

voice translation-profile NEW-BRI

translate calling 2

!

voice translation-profile NEW-BRI-Incoming

translate called 3

!

voice translation-profile PSTNIN

translate called 1

!

!

voice-card 0

no dspfarm

!

!

!

interface BRI0/2/0

no ip address

isdn switch-type basic-net3

isdn overlap-receiving

isdn point-to-point-setup

isdn incoming-voice voice

isdn static-tei 0

!

interface BRI0/3/0

no ip address

isdn switch-type basic-net3

isdn overlap-receiving

isdn point-to-point-setup

isdn incoming-voice voice

isdn static-tei 0

!

interface Dialer1

no ip address

!

voice-port 0/2/0

translation-profile incoming PSTNIN

!

voice-port 0/2/1

translation-profile incoming PSTNIN

!

voice-port 0/3/0

translation-profile incoming NEW-BRI-Incoming

translation-profile outgoing NEW-BRI

!

voice-port 0/3/1

translation-profile incoming NEW-BRI-Incoming

translation-profile outgoing NEW-BRI

!

!

dial-peer voice 30 pots

destination-pattern 900T

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

direct-inward-dial

port 0/3/0

prefix 00

!

dial-peer voice 31 pots

destination-pattern 900T

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

direct-inward-dial

port 0/2/0

prefix 00

!

Regards,

3 REPLIES 3
Highlighted
Participant

Re: Dual BRI-Lines

Hi,

     From your current config you have two dial-peers with the same preference, so the choice of BRI will be RANDOM

     If you want to control certain phones using certain voice ports I would use Class of Restriction, see guide http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml

     If your users are well behaved you could use different access digits for each port.

Craig

Highlighted
Beginner

Re: Dual BRI-Lines

Hi Craig,

Thanks for your reply.

Alright let me try this by tomorrow.

Wat about incoming calls ???

I need if some body from outside calls to 0036 call should come from BRI-0/3/0 & if to other extension call should come through 0/2/0 ??

Regards,

Highlighted
Hall of Fame Master

Re: Dual BRI-Lines

Incoming depends by telco, check with them.

CreatePlease to create content
Content for Community-Ad

Cisco COVID-19 Survey