cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
261
Views
0
Helpful
4
Replies

E1 incoming call to CUCM phone number using voice translation

nicanor00
Level 1
Level 1

Hi

I have CUCM 12 and ISR4000 with E1 card

I configured the incoming E1 call to be forwarded to cucm phone number 2001 and it work

voice-port 0/1/0:15
description E1 incomin going to CUCM
connection plar 2001

 

dial-peer voice 25 voip
description SIP-Outgoing From-GW-to-CUCM
destination-pattern .
session protocol sipv2
session target ipv4:10.10.1.12
dtmf-relay rtp-nte sip-kpml
codec g711ulaw
no vad

 

But Now I need to send some specific incoming call to a specifc internal CUCM number but it doesnt work

see below my configuration

voice-port 0/1/0:15
translation-profile incoming Aller

 

dial-peer voice 20 pots
description Incoming E1 PRI dial-peer
incoming called-number .
direct-inward-dial
port 0/1/0:15
!
dial-peer voice 25 voip
description SIP-Outgoing From-GW-to-CUCM
destination-pattern .
session protocol sipv2
session target ipv4:10.10.1.12
dtmf-relay rtp-nte sip-kpml
codec g711ulaw
no vad
!
dial-peer voice 9 pots
description Incoming E1 PRI dial-peer
incoming called-number .
direct-inward-dial
port 0/1/0:15

 

voice translation-rule 1
rule 1 /923685960/ /2002/
rule 2 /923685961/ /2005/
rule 3 /923685962/ /2005/
rule 4 /923685963/ /2005/
rule 5 /923685964/ /2001/
!
voice translation-profile Aller
translate called 1

 

It doesnt work

Please kindly help

 

 

4 Replies 4

Please see this document for details on voice translation rules.



Response Signature


b.winter
VIP
VIP

Have you checked the debugs, if your translations are even taking place?

What have you troubleshooted until now?

 

Have a look at the following debugs, or post them if you can't read them on your own:

debug voice ccapi ind 1

debug voice ccapi ind 2

debug voice ccapi ind 74

debug isdn q931

debug voice translation

Hi

The public network operator send 30 line with 30 number in the E1

I dont know the number of each of these 30 line

As i dont know the associated number on each 30 E1 channel, Is it possible to send incoming call from E1 to CUCM using the E1 line channel (1, 2 , 3 ... 30)

E1 voice gateway channel 1 to CUCM ip phone internal number 2000

E1 voice gateway channel 2 to CUCM ip phone internal number 2005

E1 voice gateway channel 3 to CUCM ip phone internal number 2006

 

voice-port 0/1/0:1

connection plar 2000

voice-port 0/1/0:2

connection plar 2005

voice-port 0/1/0:3

connection plar 2006

 

This command is the approriate to do it ?

Please advise and help

Each channel on an E1 connection does not have an individual number. With this your suggested configuration is not applicable.

If you don’t have the information about what numbers you have assigned on your circuit I would recommend you to reach out to your service provider and ask the for this information.



Response Signature


Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: