enable single button barge...............

[Sunil Jadhav]

hi. i have cisco 7945 IP phone

i want to enable single button barge in  phone UI configuration............

but i am not able to select ..............?

[Jagpreet Singh]

Hi Sunil,

     Please make sure that you are following :

http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmfeat/fsbarge.html

Also, please explain in more detail the exact problem you face while configuring it.

Regards,

Jagpreet

[Sunil Jadhav]

Hi

thanks for the reply

i am trying to do the  cbarge in cme  i have gon through this documents...........

but not get cbarge soft key  in ip Phone 7945

in the  documents

"Note To use the single button barge feature, ensure that single button barge is enabled on the device.''

i have see the single button barge in phone butcurrently  it is disable............

i am trying to do enable .? help me .........

[Jagpreet Singh]

Sunil,

I was under the impression that this was CUCM and not CME. Can you share the running configuration from the router which includes the config you have done so far for this.

Regards,

Jagpreet

[Sunil Jadhav]

No, this is CME ..............

i will give  the configuration  later

[Sunil Jadhav]

telephony-service
sdspfarm conference mute-on 111 mute-off 222
sdspfarm units 1
sdspfarm tag 1 confprof1
no privacy
no auto-reg-ephone
authentication credential admin
max-ephones 165
max-dn 500
ip source-address x.x.x.5 port 2000 secondary x.x.x.6
timeouts ringing 20
system message WELCOME TO CONTINUUM
url services http://x.x.x.7/voiceview/common/login.do
url authentication http://x.x.x.5/CCMCIP/authenticate.asp 
load 6945 SCCP69xx.9-1-1-0.loads
time-zone 39
voicemail 2000
max-conferences 8 gain -6
moh "music-on-hold.au"
multicast moh 239.10.16.4 port 2000 route x.x.x.5
web admin system name admin password
dn-webedit
time-webedit
transfer-system full-consult

ephone-dn  82  octo-line

number 3000

label Conventus7945

name Conventus7945

call-forward busy 2000

call-forward noan 2000 timeout 10

!

!

ephone-dn  500  dual-line

number 4001

!

!

ephone-template  5

softkeys remote-in-use  CBarge Newcall

softkeys hold  Resume Newcall Join

softkeys connected  TrnsfVM Park Acct ConfList Confrn Endcall Trnsfer Hold

max-calls-per-button 3

busy-trigger-per-button 2

!

ephone  82

privacy off

mac-address 5006.xxxx.F740

ephone-template 5

username "test"

type 7945

button  1:82 2:500

!

[amaia.lesta]

Hello,

As far as I know the main differences between Barge and cBarge are the following ones:

Barge (SIP)

- uses phone’s built-in bridge

- max 3 parties

- for SIP shared line only

cBarge (SCCP and SIP)

- SCCP octo-line

- SIP shared line

If you are using SCCP phones you will need to use cBarge, so you will need to configure not only Privacy,  but also:

-          A hardware conference bridge

Verify if the conference profile you have created is correctly registered with the CME by using the show sccp related commands and show dspfarm all.

-          A dedicated octo-line ephone-dn for an ad-hoc conference.

Example:

ephone-dn  100  octo-line                                          

   number 8889

   name CBargeConference

   conference ad-hoc

More details in here

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmebarge.html#wp1017969

How to Configure Barge and Privacy

#

This section contains the following tasks:

#

• SCCP: Configuring the cBarge Soft Key

#

• SIP: Enabling Barge and cBarge Soft Keys

#

• SCCP: Enabling Privacy and Privacy on Hold

#

• SIP: Enabling Privacy and Privacy on Hold

###

Prerequisites

#

• Cisco Unified CME 7.0 or a later version.

#

• Octo-line directory number is configured. See the "SCCP: Creating Directory Numbers" section.

#

• Privacy is disabled on the phone. See the "SCCP: Enabling Privacy and Privacy on Hold" section.

#

• Ad hoc hardware conference resource is configured and ready to use. See"Configuring Conferencing".

#

• Join and leave tones for hardware conference can be configured as barge entrance and exit tones. See the "SCCP: Configuring Join and Leave Tones" section.

##

Restrictions

#

• Supported only on octo-line directory numbers.

#

• Not supported for meet-me conferences.

#

• Not supported if phone user is already connected to the same ad hoc conference on the octo-line.

------------------

I hope it helps

BR

[Jagpreet Singh]

Hi Sunil,

     My apologies, could not get back to you earlier. As Aman pointed out, make sure you have a conference bridge configured. You can use the following document wherein the configuration and the need is explained in detail:

https://supportforums.cisco.com/docs/DOC-32808

Regards,

Jagpreet

[Sunil Jadhav]

Thanks

actully i configured all this but not able to see the soft-key in cisco 7945 phone.

In  cisco 7945  setting>>> device configuration >>> UI configuration>>  Single button barge is disable.

i need to  enable this

Please help me