cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
420
Views
0
Helpful
6
Replies
Highlighted
Beginner

error in cme

Hi

I have a CME installed in ISR . frequently i am getting this alert in our monitoring tool :  "  Interface VoiceEncapPeer20067 is Down for xxxxxxxx

and it's management IP is 0.0.0.0

Can anyone plese tell me what is the cause,reason for this ... is it service affecting ...

Thanks

K.S.

6 REPLIES 6
Highlighted

Can you post the results of:  "show dial-peer voice 20067" ?

Highlighted
Cisco Employee

do a show dial-peer voice 20067

also do a show dial-peer voice summ and see if the dial-peer is down

Highlighted

Pls find the dial-peer status

#show dial-peer voice 20067

VoiceEncapPeer20067

        peer type = voice, system default peer = FALSE, information type = voic

,

        description = `',

        tag = 20067, destination-pattern = `9999$',

        voice reg type = 0, corresponding tag = 0,

        allow watch = FALSE

        answer-address = `', preference=0,

        CLID Restriction = None

        CLID Network Number = `'

        CLID Second Number sent

        CLID Override RDNIS = disabled,

        rtp-ssrc mux = system

        source carrier-id = `', target carrier-id = `',

        source trunk-group-label = `',  target trunk-group-label = `',

        numbering Type = `unknown'

        group = 20067, Admin state is up, Operation state is up,

        incoming called-number = `', connections/maximum = 0/unlimited,

        DTMF Relay = disabled,

        URI classes:

            Destination =

        huntstop = enabled,

        in bound application associated: 'DEFAULT'

        out bound application associated: ''

        dnis-map =

        permission :both

        incoming COR list:maximum capability

        outgoing COR list:minimum requirement

        Translation profile (Incoming):

        Translation profile (Outgoing):

        incoming call blocking:

        translation-profile = `'

        disconnect-cause = `no-service'

        advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4

        mailbox selection policy: none

        type = pots, prefix = `',

        forward-digits 0

        session-target = `', voice-port = `50/0/115',

        direct-inward-dial = disabled,

        digit_strip = enabled,

        register E.164 number with H323 GK and/or SIP Registrar = TRUE

        fax rate = system,   payload size =  20 bytes

        supported-language = ''

        preemption level = `routine'

        bandwidth:

            maximum = 64 KBits/sec, minimum = 64 KBits/sec

        voice class called-number:

            inbound = `', outbound = `'

        dial tone generation after remote onhook = enabled

        mobility=0, snr=, snr_noan=, snr_delay=0, snr_timeout=0

        snr calling-number local=disabled, snr ring-stop=disabled, snr answer-t

o-soon timer=0

        Time elapsed since last clearing of voice call statistics never

        Connect Time = 0, Charged Units = 0,

        Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0

        Accepted Calls = 0, Refused Calls = 0,

        Last Disconnect Cause is "",

        Last Disconnect Text is "",

        Last Setup Time = 0.

        Last Disconnect Time = 0.

show dial-peer voice 20067

VoiceEncapPeer20067

        peer type = voice, system default peer = FALSE, information type = voic

,

        description = `',

        tag = 20067, destination-pattern = `9999$',

        voice reg type = 0, corresponding tag = 0,

        allow watch = FALSE

        answer-address = `', preference=0,

        CLID Restriction = None

        CLID Network Number = `'

        CLID Second Number sent

        CLID Override RDNIS = disabled,

        rtp-ssrc mux = system

        source carrier-id = `', target carrier-id = `',

        source trunk-group-label = `',  target trunk-group-label = `',

        numbering Type = `unknown'

        group = 20067, Admin state is up, Operation state is up,

        incoming called-number = `', connections/maximum = 0/unlimited,

        DTMF Relay = disabled,

        URI classes:

            Destination =

        huntstop = enabled,

        in bound application associated: 'DEFAULT'

        out bound application associated: ''

        dnis-map =

        permission :both

        incoming COR list:maximum capability

        outgoing COR list:minimum requirement

        Translation profile (Incoming):

        Translation profile (Outgoing):

        incoming call blocking:

        translation-profile = `'

        disconnect-cause = `no-service'

        advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4

        mailbox selection policy: none

        type = pots, prefix = `',

        forward-digits 0

        session-target = `', voice-port = `50/0/115',

        direct-inward-dial = disabled,

        digit_strip = enabled,

        register E.164 number with H323 GK and/or SIP Registrar = TRUE

        fax rate = system,   payload size =  20 bytes

        supported-language = ''

        preemption level = `routine'

        bandwidth:

            maximum = 64 KBits/sec, minimum = 64 KBits/sec

        voice class called-number:

            inbound = `', outbound = `'

        dial tone generation after remote onhook = enabled

        mobility=0, snr=, snr_noan=, snr_delay=0, snr_timeout=0

        snr calling-number local=disabled, snr ring-stop=disabled, snr answer-t

o-soon timer=0

        Time elapsed since last clearing of voice call statistics never

        Connect Time = 0, Charged Units = 0,

        Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0

        Accepted Calls = 0, Refused Calls = 0,

        Last Disconnect Cause is "",

        Last Disconnect Text is "",

        Last Setup Time = 0.

        Last Disconnect Time = 0.

Highlighted

HI As i have posted the Dial-peer above . please note i do not have any such dialpeer created in the CME (  dial-peer voice 20067) then why i am getting this error .

Thanks a Ton

K.S.

Highlighted

HI

Are you getting this message in Cisco Works.

We have a bug which is as follows

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCdx64809

Regards

Ronak patel

Rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
Highlighted

Hi Ronak

We Have HP NNM monitoring tool where i got this error.

Thanks

K.S.

Content for Community-Ad