cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

FXO Disconnect Tone

Marwan Urabi
Beginner
Beginner

Hi,

I have common problem FXO disconnect tone , I'm trying to make custom CPTONE in Jordan after search I found this

information from http://www.3amsystems.com/World_Tone_Database?q=Jordan,Disconnect_tone .

the result give me is ( Frequency/Hz = 420X40 ) and ( Cadence/s = 0.25 on 0.25 off ) 

I config this custom-cpton but no luck , I don't understand what mean 420X40 ? many countries one frequency 420 or 425 but

can anybody explain what mean 420X40 and how I config it 

voice class custom-cptone Orange-Jordan

 dualtone disconnect

  frequency 400 420

  cadence 250 250

 

many thanks 

Marwan

6 REPLIES 6

Marwan Urabi
Beginner
Beginner

Hi,

I upload the recording disconnect tone , I hope if anybody can analyze it and give what best values should I use .

Thanks

any idea with thanks ??

I analyzed it and it's a signal with a frequency around 425 Hz and the cadence is ~ 250 ms ON and 250 ms OFF.

so the config should be similar to this:

dualtone disconnect
frequency 425
cadence 250 250

Hi Mohamed ,

many thanks for your reply.

I test it at this configuration with fail result , the main problem when the call come from outside to AA at CUC , and when other party hang up the phone complete message and go to VM and waiting until VM message maximum time finish.

this information I get it from PSTN company.

Thank you for contacting us. According to your request kindly find  The Jordanian PSTN network specifications for stand-alone-services as follow:

 

-Dial tone -    ( 420 +/- 5 Hz x40, continuous )

-Busy tone -    (420 +/- 5 Hz x40  , 500 ms on 500 ms off )

-Congestion tone -    ( 420 +/- 5 Hz x40  , 167 ms on 167 ms off)

-Holding tone -   420x40   0.5 on 8.0 off (1400 +/- 50 Hz x40 , 400 ms on 1500 ms off) 

-Howler tone -   950   continuous ( 3000 +/- 5 Hz, continuous )

-Intrusion tone -    (1400 +/- 50 Hz x40 ,  2 s on 15 s off  400 ms on)

-Number unobtainable tone -   ( 420 +/- 5 Hz x40 ,  announcement )

-Ringing tone -    ( 420 +/- 5 Hz x40 , 1200 ms on 4800 ms off )

-Special information tone ( f1=950 +/- 50 Hz, f2 = 1400 +/- 50 Hz, f3 = 1800 +/- 50 Hz.) x40 ,  (1000 ms on 1000 ms off)

-Call waiting tone -    (1400 +/- 50Hz x40, 175 ms on 175 ms off 175 ms on 3500 ms +/-1500ms off)

 

signal modulated by 40

 

 

That's strange!

Can you post your show-run to double check that the dualtone disconnect configuration is correctly applied to voice ports ?

Also, try the busy tone variant that your telco gave you (change the cadence from 250-250 to 500-500 )

Hi,

below the configuration for FXO port , I use the cptone BR because when I choice JO Caller ID will not work also the 2 command :-

caller-id alerting line-reversal
caller-id alerting dsp-pre-allocate

not acceptable at cptone JO , by the way I have other brach have CME it's work perfectly the cptone JO and caller ID also disconnect tone work .

voice class dualtone-detect-params 1
freq-max-deviation 25
freq-max-power 0
freq-min-power 13
freq-power-twist 4
cadence-variation 4


voice class custom-cptone Jordan
dualtone disconnect
frequency 420
cadence 500 500

voice-port 0/0/0
trunk-group Orange 2
translation-profile incoming PSTN-Fix-CallerID
supervisory disconnect dualtone mid-call
supervisory custom-cptone Jordan
supervisory dualtone-detect-params 1
cptone BR
timeouts call-disconnect 2
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 50
timing guard-out 1000
timing sup-disconnect 100
connection plar opx 611
description **Line 1**
caller-id enable
caller-id alerting line-reversal
caller-id alerting dsp-pre-allocate
!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: