04-23-2013 06:16 PM - edited 03-16-2019 04:58 PM
Hello people,
I'm newer inside Cisco voip and I wonder it's possible do an communication between FXS and FXO ?
I have two router device one with FXS Interface witch has a analog phone pluged and other router has a PABX that supplies FXO Interface.
I need do called between each other, it's possible ?
if someone has an tip about how to please post here or any doc about
thanks
04-24-2013 03:37 AM
Yes it's possible. Simply a matter of dial-peers. Related reading:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800ae2d1.shtml
Here's an overly simplified config example. There are many additional command options but this gets the ball rolling:
!The FXO port
voice-port 0/1/0
!Where you want the router to direct incoming calls
connection plar opx 1234
caller-id enable
!The FXS port
voice-port 0/2/0
station-id name Example
station-id number 1234
dial-peer voice 100 pots
destination-pattern
port 0/1/0
dial-peer voice 200 pots
destination-pattern 1234
port 0/2/0
Please remember to rate helpful responses and identify helpful or correct answers.
05-03-2013 08:39 AM
Hello,
Thank you Jonathan for your tip.
I had done a test but unsuccess. I don't know why but my Interface FXO seems no detect the ring pulse because when into a call from my PABX to the extention it's pluging in that FXO nothing happen.
I think there is some tuning to do at the configuration about ring, pulse, etc. but I don't know where neither how to
any tip about how to tuning that it's welcome.
thanks
05-07-2013 05:51 PM
Hello,
Sorry my persistence about that issue below follow parts of configuration and a draw.
My problem is when the call come from of extention 21 ( FXO ) to extention 2000 ( FXS ) of course numer dialer is 20 ( number of extention PABX ) but nothing happen on router A. when I turn on debug nothing appear! I Think should shows anything on console but nothing. so I wonder what is happen ?
When the call come from FXS interface to FXO it's work!
any tip about is welcome
Configuration on Router A
voice-port 0/1/0
connection plar opx 2000
caller-id enable
dial-peer voice 100 pots
destination-pattern 21
port 0/1/0
dial-peer voice 101 voip
destination−pattern 2000
dtmf−relay h245−alphanumeric
session target ipv4:10.80.80.1
Configuration on Router B
voice-port 0/2/0
station-id name example
station-id number 2000
cptone BR
supervisory disconnect signal
dial-peer voice 200 pots
destination-pattern 2000
port 0/2/0
dial−peer voice 201 voip
destination−pattern 21
dtmf−relay h245−alphanumeric
session target ipv4:10.80.80.2
05-07-2013 08:49 PM
Hi,
Please capture the following debugs on both routers for the not working call:
deb voice ccapi inout
deb vpm signal
deb h225 asn1
Do "term mon" and/or "logging console" and capture the output.
--
Jorge Armijo
Please remember to rate helpful responses and identify helpful or correct answers.
05-08-2013 03:57 PM
Thank you Jorge I'm going that test on friday and come back here next week.
thanks
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: