Hello!
i have cisco2911 with 151-4.M3 IOS, gateway configured as h.323 gw on Cisco CUCM.
when i made outside call to PSTN from IP phone i got message
Invalid number format
after
TX -> INFORMATION which gw send to PSTN
Aug 14 05:31:25.359: ISDN Se0/0/0:15 Q931: Sending SETUP callref = 0x00F4 callID = 0x8077 switch = primary-net5 interface = User
Aug 14 05:31:25.359: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x00F4
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838A
Exclusive, Channel 10
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x2181, '8xxx420494'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '8xxx3815299'
Plan:ISDN, Type:National
Aug 14 05:31:25.379: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x80F4
Channel ID i = 0xA9838A
Exclusive, Channel 10
Aug 14 05:31:25.379: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x80F4
Progress Ind i = 0x8288 - In-band info or appropriate now available
Aug 14 05:31:28.959: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x80F4
Aug 14 05:31:35.359: ISDN Se0/0/0:15 Q931: TX -> INFORMATION pd = 8 callref = 0x00F4
Sending Complete
Aug 14 05:31:35.371: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x80F4
Cause i = 0x829C - Invalid number format (incomplete number)
Progress Ind i = 0x8288 - In-band info or appropriate now available
Display i = 'WRONG NUMBER '
But if i push button "Redial" on IP phone call go with out problem and i don't see message
Aug 14 05:31:35.359: ISDN Se0/0/0:15 Q931: TX -> INFORMATION pd = 8 callref = 0x00F4
Sending Complete
Aug 14 05:32:01.838: ISDN Se0/0/0:15 Q931: Sending SETUP callref = 0x00F5 callID = 0x8078 switch = primary-net5 interface = User
Aug 14 05:32:01.838: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x00F5
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838A
Exclusive, Channel 10
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x2181, '8xxx420494'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '8xxx3815299'
Plan:ISDN, Type:National
Aug 14 05:32:01.854: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x80F5
Channel ID i = 0xA9838A
Exclusive, Channel 10
Aug 14 05:32:01.858: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x80F5
Progress Ind i = 0x8288 - In-band info or appropriate now available
Aug 14 05:32:05.106: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x80F5
Aug 14 05:32:17.714: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x80F5
Cause i = 0x8391 - User busy
Progress Ind i = 0x8288 - In-band info or appropriate now available
Display i = 'BUSY
How to get rid of INFORMATION message?
Best regards,
Mike
