cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1131
Views
5
Helpful
6
Replies

How can i access ATA using web browser..?

midhun_km
Beginner
Beginner

As like Ip phone

http://<ip add of phone>................

is there any possible way to open the ATA 186 registerd with call manager....?

urgent Plz help me.......

6 Replies 6

Jaime Valencia
Hall of Fame Cisco Employee Hall of Fame Cisco Employee
Hall of Fame Cisco Employee

From the PC, open a Web browser and enter this  URL: http:///dev.

http://www.cisco.com/en/US/partner/products/hw/gatecont/ps514/products_configuration_example09186a00800c3a50.shtml

HTH

java

If this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

Hi java ..

Thanks Dude................

Exactly what i want is this.....

Hi Java,

I'm facing some problem with switch ports conneted to ATA.

from the switch log window its contunuslly showing the message

2011-03-07 10:28:5523410.40.6.207*Mar 10 19:40:40: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/39 (not half duplex), with SEP0026CBBE8C61 Port 1 (half duplex).
2011-03-07 10:28:5323410.40.8.234.Mar 6 20:52:25: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/25 (not half duplex), with SEP64168D51BAD2 Port 1 (half duplex).
2011-03-07 10:28:3123410.40.8.233.Mar 7 04:30:32: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/11 (not half duplex), with SEP0026CBBE8C63 Port 1 (half duplex).

Whenever  i compare the  ATA conneted with one the switch ports above shown with another perfectly working ATA's using http:///dev

inside the both ATA's webpage showing the same denominations for all the attibutes.

I changed the duplex of each switch port to half duplex then the switch log window message is get inverted. like.......

011-03-07 10:28:5523410.40.6.207*Mar 10 19:40:40: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/39 (not full duplex), with SEP0026CBBE8C61 Port 1 (full duplex).
2011-03-07 10:28:5323410.40.8.234.Mar 6 20:52:25: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/25 (not full duplex), with SEP64168D51BAD2 Port 1 (full duplex).
2011-03-07 10:28:3123410.40.8.233.Mar 7 04:30:32: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/11 (not full duplex), with SEP0026CBBE8C63 Port 1 (full duplex).

so the also tried with duplex auto, message is same...

and also i try with all the 9 combinations ..................

duplex auto . speed auto,100,10

duplex half. speed auto,100,10

duplex full . speed auto,100,10

So how can i resolve the problem...?

HI Midhun,

Did you tried a shut and no shut after making the duplex changes in the ports .

Hi Midhun,

The %CDP-4-DUPLEX_MISMATCH messages may be generated repeatedly when Cisco Discovery Protocol (CDP) has discovered a mismatch of duplex configuration between CDP neighbors.

This message occurs when a duplex mismatch is detected between CDP neighbors. It can also occur when switches are separated by a non-Cisco switch or hub. If CDP version 2 reports the link as a half-duplex when a port or interface on a CDP-enabled device has been configured or auto negotiated to full-duplex, the alternate device may not support CDP version 2. This causes the error to occur. It is a cosmetic issue.

CDP is useful for detecting errors as well as port and system statistics on neighboring Cisco devices. CDP is Cisco proprietary and works be sending packets to a well-known MAC address 01-00-0C-CC-CC-CC.

To resolve this issue, perform these steps:

  1. To disable CDP version 2, issue the no cdp advertise-v2 command. 

  2. To check the CDP version running on the device, issue the show cdp command.

       
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers