10-24-2013 09:41 AM - edited 03-16-2019 08:03 PM
Have a public phone line connected to my CUCME 2801 router VIC2-2FXO card. All inbound calls are passed to DN-5001 (group number). Can receive and send calls without a problem, but incoming calls all show "911" for caller ID. Think this is simply an issue with the out bound dial-peer, of which the lowest numbered out bound dial-peer is for 911 services. Not sure how to correct this so inbound calls show the proper caller ID?
Below is a copy of my CUCME show run output from the FXO port config thru all the dial-peers. Any pointers is greatly appreciated.
Thanks.
Kirk E.
!
voice-port 0/0/0
connection plar opx immediate 5001
!
voice-port 0/0/1
!
voice-port 0/2/0
station-id name POTS
station-id number 7000
!
voice-port 0/2/1
!
ccm-manager config
!
!
dial-peer voice 7000 pots
destination-pattern 5006
port 0/2/0
!
dial-peer voice 90 pots
description Emergency Services
destination-pattern 911
port 0/0/0
forward-digits 3
!
dial-peer voice 91 pots
description 10 Digit local dialing
destination-pattern [234].........
port 0/0/0
forward-digits 10
!
dial-peer voice 92 pots
description 11 Digit local/long distance dialing
destination-pattern 1[2348].........
port 0/0/0
forward-digits 11
!
dial-peer voice 93 pots
description Long Distance
destination-pattern 011T
port 0/0/0
prefix 011
!
dial-peer voice 94 pots
description Backup bench POTS phone
destination-pattern 7000
port 0/2/0
!
dial-peer voice 2 voip
destination-pattern 51..
session protocol sipv2
session target ipv4:172.16.2.155
dtmf-relay sip-notify
codec g711ulaw
no vad
!
!
Solved! Go to Solution.
10-25-2013 06:40 AM
Correct, always shut/unshut.
Please mark the question as answered if you have no further questions.
Chris
10-24-2013 10:13 AM
Add "caller-id enable" to the voice-ports.
Chris
10-24-2013 02:17 PM
Chris,
Thanks, but that didn't work.
I added "caller-id enable" to voice-port 0/0/0 (where the outside line plugs in) but it did not fix the issue. Called again and still got 911 as the caller-id. I know a good caller-id is being passed in because it shows up on a POTS phone tied off the same line.
Kirk
10-24-2013 02:26 PM
Perhaps caller ID is not available on the line, please provide the following:
debug vpm singnal
debug voice ccapi inout
Chris
10-24-2013 05:28 PM
Hi
Can you find the below:-
Hi
1- Please find the below table as the following link http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml
Caller ID Requires VIC-2FXO-M1, VIC-2FXO-M2, VIC-4FXO-M1, VIC2-2FXO, VIC2-4FXO, or MRP3-8FXOM1
under voice-port
caller-id enable
2-If above configure and still have no caller id , please add the below commannds to the voice-port
caller-id alerting line-reversal
cptone ? "based on your"
caller-id alerting ring 2 "the default is 1" maximum number of rings to be detected before a call is answered over an FXO voice port.
4-Do debug to make sure all ok
"debug vpm signal "
[0/3/0] get_fxo_caller_id:Caller ID received. Message type=128 length=31 checksum=74
Thank you
please rate all useful information
10-24-2013 06:47 PM
I've seen this before, try this:
current setting:
dial-peer voice 90 pots
description Emergency Services
destination-pattern 911
port 0/0/0
forward-digits 3
new:
dial-peer voice 90 pots
destination-pattern 91[1] <-- Modify the pattern like this
or
destination-pattern 91[.]
Just avoid a complete number match, I prefer the first one.
Give it a try and let me know.
~jorge
10-24-2013 06:51 PM
All,
It is working now. After I added the caller-id enable I didn't stop, start the interface. Took me a bit to think of that. Now it is working well.
Thanks to all.
Kirk
10-24-2013 06:55 PM
Hi
Congratulations for you , please donot forget to rate all useful information for all of here.
Thank you
please rate all useful information
10-25-2013 06:40 AM
Correct, always shut/unshut.
Please mark the question as answered if you have no further questions.
Chris
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide