10-24-2013 09:41 AM - edited 03-16-2019 08:03 PM
Have a public phone line connected to my CUCME 2801 router VIC2-2FXO card. All inbound calls are passed to DN-5001 (group number). Can receive and send calls without a problem, but incoming calls all show "911" for caller ID. Think this is simply an issue with the out bound dial-peer, of which the lowest numbered out bound dial-peer is for 911 services. Not sure how to correct this so inbound calls show the proper caller ID?
Below is a copy of my CUCME show run output from the FXO port config thru all the dial-peers. Any pointers is greatly appreciated.
Thanks.
Kirk E.
!
voice-port 0/0/0
connection plar opx immediate 5001
!
voice-port 0/0/1
!
voice-port 0/2/0
station-id name POTS
station-id number 7000
!
voice-port 0/2/1
!
ccm-manager config
!
!
dial-peer voice 7000 pots
destination-pattern 5006
port 0/2/0
!
dial-peer voice 90 pots
description Emergency Services
destination-pattern 911
port 0/0/0
forward-digits 3
!
dial-peer voice 91 pots
description 10 Digit local dialing
destination-pattern [234].........
port 0/0/0
forward-digits 10
!
dial-peer voice 92 pots
description 11 Digit local/long distance dialing
destination-pattern 1[2348].........
port 0/0/0
forward-digits 11
!
dial-peer voice 93 pots
description Long Distance
destination-pattern 011T
port 0/0/0
prefix 011
!
dial-peer voice 94 pots
description Backup bench POTS phone
destination-pattern 7000
port 0/2/0
!
dial-peer voice 2 voip
destination-pattern 51..
session protocol sipv2
session target ipv4:172.16.2.155
dtmf-relay sip-notify
codec g711ulaw
no vad
!
!
Solved! Go to Solution.
10-25-2013 06:40 AM
Correct, always shut/unshut.
Please mark the question as answered if you have no further questions.
Chris
10-24-2013 10:13 AM
Add "caller-id enable" to the voice-ports.
Chris
10-24-2013 02:17 PM
Chris,
Thanks, but that didn't work.
I added "caller-id enable" to voice-port 0/0/0 (where the outside line plugs in) but it did not fix the issue. Called again and still got 911 as the caller-id. I know a good caller-id is being passed in because it shows up on a POTS phone tied off the same line.
Kirk
10-24-2013 02:26 PM
Perhaps caller ID is not available on the line, please provide the following:
debug vpm singnal
debug voice ccapi inout
Chris
10-24-2013 05:28 PM
Hi
Can you find the below:-
Hi
1- Please find the below table as the following link http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml
Caller ID Requires VIC-2FXO-M1, VIC-2FXO-M2, VIC-4FXO-M1, VIC2-2FXO, VIC2-4FXO, or MRP3-8FXOM1
under voice-port
caller-id enable
2-If above configure and still have no caller id , please add the below commannds to the voice-port
caller-id alerting line-reversal
cptone ? "based on your"
caller-id alerting ring 2 "the default is 1" maximum number of rings to be detected before a call is answered over an FXO voice port.
4-Do debug to make sure all ok
"debug vpm signal "
[0/3/0] get_fxo_caller_id:Caller ID received. Message type=128 length=31 checksum=74
Thank you
please rate all useful information
10-24-2013 06:47 PM
I've seen this before, try this:
current setting:
dial-peer voice 90 pots
description Emergency Services
destination-pattern 911
port 0/0/0
forward-digits 3
new:
dial-peer voice 90 pots
destination-pattern 91[1] <-- Modify the pattern like this
or
destination-pattern 91[.]
Just avoid a complete number match, I prefer the first one.
Give it a try and let me know.
~jorge
10-24-2013 06:51 PM
All,
It is working now. After I added the caller-id enable I didn't stop, start the interface. Took me a bit to think of that. Now it is working well.
Thanks to all.
Kirk
10-24-2013 06:55 PM
Hi
Congratulations for you , please donot forget to rate all useful information for all of here.
Thank you
please rate all useful information
10-25-2013 06:40 AM
Correct, always shut/unshut.
Please mark the question as answered if you have no further questions.
Chris
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: