INSTALL CME 12 IN ROUTER ISR4321/K9

[Jose Salazar]

Hello

I have a router isr 4300 image isr4300-universalk9.16.06.05.SPA.bin and rommon isr4200_4300_rommon_169_1r_SPA.pkg. I have transfer the CME ver 12

CME-COMPLETE-FILESET-12.0.tar

cme-full-locale-12.0.tar

CME-GUI-12.0.tar

I used the command 

Archive tar /xtract  ftp://192.168.1.30/CME-COMPLETE-FILESET-12.0.tar flash:

I am following same procedure for each .tar

The file has been extracted and it created the folder for each one. I reloaded however, when I go to config terminal, the command telephony-service is missing. What do I missing here?

flash

CMEDIR

[Jaime Valencia]

You do not have a UC license to use CME

https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/manual/cmeadm/cmeover.html#concept_779AC8A8399D4294AB699248BB5302F2

CME is already embedded in the IOS, you do not need to "install" CME.

[HARIS_HUSSAIN]

For Activation evalutaion CUCME Featues use below command.

Router#show license all
........
StoreIndex: 1 Feature: uck9 Version: 1.0
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
Evaluation total period: 8 weeks 4 days
Evaluation period left: 8 weeks 4 days
Period used: 0 minute 0 second
License Count: Non-Counted
License Priority: None

For Reference
• Use below commands to activate the evaluation uc feature
o license boot module <routermodel>  technology-package uck9
o reload

For Smart Licensing refer below

On the Unified CME router, you need to ensure that the call home feature is not disabled. Also, Smart Licensing feature should be enabled at the router using the CLI command license smart enable . Use the no form of the command to disable smart licensing. For more information on configuring Smart Licensing in your router, see Software Activation Configuration Guide, Cisco IOS Release 15M&T. Once the smart license is enabled and the router is not yet registered with CSSM, the device enters an evaluation period of 90 days.

You can register the router to CSSM with the token ID. To register the device (Unified CME router) with CSSM, use the CLI commandlicense smart register idtoken . For information on registering the device with CSSM, see Software Activation Configuration Guide.

*** Please rate helpful post; Mark "Accept as a Solution" if applicable

Thanks,
Haris

[Leo Laohoo]

---

@HARIS_HUSSAIN wrote:

License State: Not in Use, EULA not accepted

---

No `tis not.  "Not In Use" because "EULA not accepted".  So this means the License isn't activated and cannot be used (until EULA is accepted). 

conf t
 license accept end user agreement 
end
wr

[edwincharles]

Hello,

what will happen after the period left is consumed for cme-srst

Feature: uck9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium

Feature: cme-srst
Period left: 7 weeks 4 days
Period Used: 6 days 19 hours
License Type: EvalRightToUse
License State: Active, In Use
License Count: 100/0 (In-use/Violation)
License Priority: Low

[Roger Kallberg]

It will automatically transition to right to use. 
For more details please check this document, https://community.cisco.com/t5/collaboration-voice-and-video/understanding-cme-srst-license-activation/ta-p/3123270