Re: its-CISCO.2.0.2.0.tcl script on Cisco 2800 problem

hiepnguyenho · ‎04-22-2010

Dear all,

I have a problem with its-CISCO.2.0.2.0.tcl script. I downloaded this file from Cisco and run on my Cisco 2800 voice gateway. The problems are:

- I can not hear prompt. I take a inbound call from PSTN, it connect but no prompt.

- I press 0 for operator but it takes about 10 seconds to connect to operator number. It's too long, right? How can I fix it?

Here are some outputs of configuration, flash: content and debug voice application script:

Configuration:

!
voice class custom-cptone vn
dualtone disconnect
frequency 425 425
cadence 500 500 continuous
!
voice-card 0
!
application
service inbound_ivr flash:its-CISCO.2.0.2.0.tcl
param aa-pilot 499
paramspace english index 0
paramspace english language en
paramspace english location flash:
param operator 4100
paramspace english prefix en

!

!
voice-port 0/3/0
supervisory disconnect dualtone mid-call
supervisory custom-cptone vn
supervisory dualtone-detect-params 1
no battery-reversal
timeouts call-disconnect 1
timeouts ringing 5
caller-id enable

!

!
dial-peer voice 29 pots
description PSTN number 7722086
service inbound_ivr
destination-pattern .T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 0/3/0
forward-digits all

!

dial-peer voice 4 voip
description ***** Inbound to HAN *****
destination-pattern 4...
modem passthrough nse codec g711alaw redundancy
session target ipv4:172.28.83.2
dtmf-relay rtp-nte
codec g711ulaw
no vad

FLASH:

Directory of flash:/

    1 -rw-    59846440                    <no date> c2800nm-adventerprisek9_ivs-mz.124-24.T.bin
    2 -rw-      198423                    <no date> track2v.au
   22 -rw-        5962                    <no date> welcome5.tcl
   23 -rw-        7464                    <no date> oscv4_final.tcl
   24 -rw-     1016832                    <no date> app-b-acd-3.0.0.2-ReadMe.txt
   25 -rw-       30421                    <no date> app-b-acd-3.0.0.2.tcl
   26 -rw-       55599                    <no date> app-b-acd-aa-3.0.0.2.tcl
   27 -rw-       75650                    <no date> en_bacd_allagentsbusy.au
   28 -rw-       83291                    <no date> en_bacd_disconnect.au
   29 -rw-       63055                    <no date> en_bacd_enter_dest.au
   30 -rw-       37952                    <no date> en_bacd_invalidoption.au
   31 -rw-      496521                    <no date> en_bacd_music_on_hold.au
   32 -rw-      123446                    <no date> en_bacd_options_menu.au
   33 -rw-       42978                    <no date> en_bacd_welcome.au
   34 -rw-       42978                    <no date> _bacd_welcome.au
   36 -rw-        5962                    <no date> welcome_hcm.tcl
   39 -rw-        7156                    <no date> its-CISCO.2.0.2.0.tcl
   40 -rw-      198423                    <no date> _welcome.au
   42 -rw-      198423                    <no date> en_welcome.au

debug voice application script

*Apr 23 05:51:10.711: //106//TCL :/tcl_PutsObjCmd: proc act_Setup
*Apr 23 05:51:10.711:
*Apr 23 05:51:10.711: //106//TCL :/tcl_PutsObjCmd:
proc init_perCallvars
*Apr 23 05:51:10.711:
*Apr 23 05:51:10.711: //106//TCL :/tcl_PutsObjCmd:
ANI
*Apr 23 05:51:10.711:
*Apr 23 05:51:10.711: //106//TCL :/tcl_PutsObjCmd:
DNIS
*Apr 23 05:51:10.711:
*Apr 23 05:51:10.711: //106//TCL :/tcl_PutsObjCmd:
No DNIS

*Apr 23 05:51:10.711: <----------------------------------------------- I press 0 here
*Apr 23 05:51:33.891: //106//TCL :/tcl_PutsObjCmd:
proc act_GotDest <----------------------------------------------------- connect to operator number here.
*Apr 23 05:51:33.891:
*Apr 23 05:51:45.243: //106//TCL :/tcl_PutsObjCmd:
Connection success
*Apr 23 05:51:45.243:

Could you please tell me how to fix it? Thank you very much.

william_chua · ‎04-23-2010

I have this TCL application working before.

Try configuring a simple inbound dial-peer like shown below:

dial-peer voice 29 pots

service inbound_ivr

incoming called number 7722086

port 0/3/0

hiepnguyenho · ‎04-23-2010

Thanks William. Last time when you run this application script, how did you name the prompt file. I mean en_welcome.au or _welcome.au? Is there any more param to be configured for this?

william_chua · ‎04-23-2010

i did not rename any prompts. I just uncompressed the tar file to the flash of the router.

hiepnguyenho · ‎04-24-2010

I find my problem is:

- I press 0 while the prompt is playing and it takes 10 seconds to connect to the operator.

- I press 0 after the prompt and it connect to the operator immediately.

So my question is what if my prompt is long and a person from PSTN want to press 0 before the prompt end. Is there any way to modify the script to do it?