cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Cisco Community Designated VIP Class of 2020

1072
Views
0
Helpful
12
Replies
Beginner

Meeting Place 7.0

Hi,

I received today meeting-place servers contain (Application Server,Media Server,Web Conferencing Server). Could any one has a step by step installation and configuration guide.

Regards,

Ali Nasser

12 REPLIES 12

Meeting Place 7.0

The documentation available is on the product page (and linked DocWiki in some cases): http://www.cisco.com/en/US/partner/products/sw/ps5664/ps5669/tsd_products_support_series_home.html

If you're a partner there is also a PEC course or two on the topic; just search for MeetingPlace.

Meeting Place 7.0

Hi Ali

this is the link to the cisco doc wiki which has a lot  of useful documents for MP 7

http://docwiki.cisco.com/wiki/Category:Reference_Information_for_Cisco_Unified_MeetingPlace%2C_Release_7.0

keep in mind when you start the setup install and make the basic setup of the application server first then you can integrate the media server after and last think setup the internal and external we servers

HTH

Beginner

Meeting Place 7.0

Hi Marwan,

I configure the application server and i did the integration with web server,  i test the web conferencing but i facing one issue the integration eith CUCM i configure as document but i can't dial the meeting place number its give fast busy tone i review the configuration in call manager which is (SIP trunk and the ip assgin is application server, RP,RL,RG,SIP security profile,and extension) all are in the same CSS which has access to the SIP trunk.

Please advise.

Regards,

Ali Nasser 

Re: Meeting Place 7.0

Hi Ali

hav eyou configured the SIP trunk side from Meeting ? also if you have a CUCM cluster make sure in meeting place you put the CUCM tat doig call processing first whcih might be the subsecriber IP ( you can check this from CUCM groups )

also have you registered the media server/blade to the application server ? if not you need to do it first

just include all the IPs of CUCM cluster server and make sure you are using the right SIP port interms of in/out UDP or tcp

HTH

Highlighted
Cisco Employee

Meeting Place 7.0

Hi,

You can also try running "cptrace -t" on meeting place and make a test call. That will clarify if the call is even hitting MP.

-Atul

Please rate, if this helps !!

Beginner

Re: Meeting Place 7.0

Hi Atul,

I run this command here what i get

My extension is 2222

and MP extension is 3333

please check below.

08/17 12:33:00.58       P 0      In Call : DID/DNIS 3333, ANI 2222 ==========(1)

08/17 12:33:00.58       P 0      Action : DETERMINEAPP

08/17 12:33:00.58       P 0      Action : GOTOAPP

08/17 12:33:00.58       P 0      Applicat : MEETING DIRECT

08/17 12:33:00.58       P 0      Action : ANSWERCALL

08/17 12:33:14.92       P 1      In Call :  DID/DNIS 3333, ANI 2222 ==========(2)

08/17 12:33:14.92       P 1      Action : DETERMINEAPP

08/17 12:33:14.92       P 1      Action : GOTOAPP

08/17 12:33:14.92       P 1      Applicat : MEETING DIRECT

08/17 12:33:14.92       P 1      Action : ANSWERCALL

08/17 12:33:31.58       P 0      Action : CLEANUPCALL

08/17 12:33:31.58       P 0      Action : USER_SAVEPROFILE

08/17 12:33:31.58      P 0      Action : WRITE OD STATS

08/17 12:33:31.58      P 0      Action : DISCONNECTCALL

Please Advise

Ali Nasser

Beginner

Re: Meeting Place 7.0

Hi Marwan,

Hope you are doing well,

From the meetingplace i configure the CUCM IP under system configuration------call configuration--------SIP configuration. In SIP configuration

SIP Configuration

Display Name : MeetinPlace

Username : (The phone number with is configure in usage configuration-----Access phone number 1(3333)

SIP domain name (Blank)

SIP Proxy Server 1

Hostname or IP address : CUCM ip address

Port : 5060

Transport : TCP

Is these configuration are correct.

and for the media server please send to me how to configure it under the meetingplace

Please Advise,

Regards,

Ali Nasser

Meeting Place 7.0

have you integrated the media server with the application server yet ?

also go to System Configuration > Usage Configuration

then access number 1 and this need to be same as the username/number 3333  change this value requres restart

Only accept incoming calls from prox make sure it is NO

also make sure that CUCM use TCP for outgoing SIP calls over this trunk

Beginner

Re: Meeting Place 7.0

No not yet, i am asking for the steps if you have.

Regards,

Beginner

Meeting Place 7.0

Hi,

I'm having the same issue. I have configured everything as above. Verified CUCM routing is fine from DNA.

When i call into Meeting Place i get a fast busy tone.

Then only thing i did different is instaed of using TCP as the transport layer i using UDP. Cause Cisco doc said UDP is recommend. Both is CUCM and Meeting Place is configured for UDP.

This is was i got from the log. It look similiar to the issue here.

02/27 16:03:16.09  P 0       In Call  : DID/DNIS 6395, ANI 6331 ============= (1)

02/27 16:03:16.09  P 0       Action   : DETERMINEAPP

02/27 16:03:16.09  P 0       Action   : GOTOAPP

02/27 16:03:16.09  P 0       Applicat : MEETING DIRECT

02/27 16:03:16.09  P 0       Action   : ANSWERCALL

02/27 16:03:47.10  P 0       Action   : CLEANUPCALL

02/27 16:03:47.10  P 0       Action   : USER_SAVEPROFILE

02/27 16:03:47.10  P 0       Action   : WRITE OD STATS

02/27 16:03:47.10  P 0       Action   : DISCONNECTCALL

Beginner

Meeting Place 7.0

I also notice from CUCM SDI traces,  SIP 503 error coimg from the Meeting Place server:

02/27/2012 17:15:19.006 CCM|//SIP/SIPUdp/wait_UdpDataInd: Incoming SIP UDP message size 335 from 10.9.13.149:[5060]:

SIP/2.0 503 Service Unavailable

From: <6331>;tag=56476da0-74f1-4249-bfee-fa08a0b25000-35172000

To: <6395>;tag=ad66c2b0-0-13c4-594ca2-44ebacab-594ca2

Call-ID: 8fa55c80-f4b149a6-22-8e0d090a@10.9.13.142

CSeq: 101 INVITE

Via: SIP/2.0/UDP 10.9.13.142:5060;branch=z9hG4bKaf7f284a59

Content-Length: 0

Beginner

Meeting Place 7.0

Hi Ali Nasser,

May i know, how you sloved this issue.

I'm have the exact same issue you were facing.

Regards,

Subash

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here