cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
635
Views
13
Helpful
7
Replies

multiple conferencing in cisco ccme 2951 ver 7.1 with PRI line

zeuscyril
Level 4
Level 4

hi all,

i need to do multoparty confernce using cisco ccme 7.1 (cisco2951).

i my system 3 party conference is working means 2 outside numbers and one local extension , but i need to configure for 5 people from outside and one from local . that is not happening .

is it possible from normal ccme itself or we need to buy any license or hardware part.

because we are having PRI line with 30 channels but still only 3 party is working.

thanks

cyril

7 Replies 7

Jaime Valencia
Cisco Employee
Cisco Employee

For more than 3 party conferences you need to configure a HW CFB.

HTH

java

If this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

gagansi
Level 1
Level 1

Hi Cyril,

To allow hardware-based multi-party ad hoc conferences with more than  three parties and meet-me conferences, perform the following steps.

Here are the steps-->

## Enable

## Configure- Terminal

## Telephony-Service

## Confrence Hardware

## Transfer system Full-consult

## sdspfarm units number

## Sdspfarm tag number device-name

## sdspfarm confrence mute-on  mute-on-digits mute-off  mute-off-digits

He is the link for refrence-

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeconf.html#wp1011144

For hardware confrence you need the DSPs on the Router.

Please Rate if found Useful.

/Gagan

hi singh,

once i enabled conference hardware in telephony service my normal 3 party confernce also not working.

only one party able to communicate at a time .

we need any license for hardware confernce or any differnt way to dial a confernce call (or) normal way.

i added confernce list conference rmlsc select join all these softkeys in the conference phone.

if i remove conference hardware comand from telephony service i can able to call 3 party confernce.

i changed the ephone-dn to octo line also.

so please give me the solution.

thanks

cyril

Hi

The dialing way is the same as u r used to it.

Configuring multi-party ad hoc conferencing in Cisco Unified CME disables three-party (software-based) ad hoc conferencing.

Please attach your config.

/Gagan

hi singh,

i am posted my config already can u check and let me know the solution.

i am waiting for ur response

thanks

cyril


here the config

sh run
Building configuration...


Current configuration : 32903 bytes
!
! Last configuration change at 18:50:06 UAE Mon Jun 6 2011 by admin
! NVRAM config last updated at 18:28:20 UAE Mon Jun 6 2011 by admin
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname LOME
!
boot-start-marker
boot-end-marker
!
card type e1 0 0
logging buffered 51200 warnings
!
no aaa new-model
clock timezone UAE 4
network-clock-participate wic 0
network-clock-select 1 E1 0/0/0
--More--                           !
no ipv6 cef
ip source-route
ip cef
!
!
!
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
!
!
!
isdn switch-type primary-net5
!
!
crypto pki trustpoint TP-self-signed-1105286637
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1105286637
revocation-check none
rsakeypair TP-self-signed-1105286637
!
--More--                           !
crypto pki certificate chain TP-self-signed-1105286637
certificate self-signed 01
  3082024B 308201B4 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
  31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
  69666963 6174652D 31313035 32383636 3337301E 170D3130 31313239 31363036
  31365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
  4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 31303532
  38363633 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
  8100B7FE A973D6ED 71FF0873 A9296649 F8B355C5 0FC38AE6 56E6C2E7 B14DB21B
  93BC91DB 829DEADB A4C3FD29 140999AB D8C0BF0A AC3BE0D2 24F63AF6 7C0DF58C
  45339CD0 05CB9AA1 0E3A632A 2CAD4566 2E7A6693 D683F7D5 E1A7D591 162493C4
  04CBE928 464325A2 45B2EA12 9B77973E 5F36327B 2602AB39 BFB899C7 10A1F454
  7FEF0203 010001A3 73307130 0F060355 1D130101 FF040530 030101FF 301E0603
  551D1104 17301582 134C4F4D 452E796F 7572646F 6D61696E 2E636F6D 301F0603
  551D2304 18301680 14218A80 B4BFD05D 0ADBAA05 B202E252 E014F21E 67301D06
  03551D0E 04160414 218A80B4 BFD05D0A DBAA05B2 02E252E0 14F21E67 300D0609
  2A864886 F70D0101 04050003 8181006B 0E54FBF4 46163A9D 5D4C53EF F7AB19C1
  6109CD11 70612622 EE72BAA1 91ABA20F 7D66C3F8 4AE444FC 04D5F53C EF03E1CC
  2C7BEA5B 19A324ED 8CC0CD72 DB4429DE 4AC7FCB5 19751121 FD9CB2B3 232DC59E
  BFD83A98 9F323799 2BA33B43 96C65D66 EF9BB363 80FD9B98 52EBEAEF 3331D5FF
  041D71DD 30F18B8A 724BA760 36EB59
   quit
--More--                           voice-card 0
dsp services dspfarm
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol pass-through g711ulaw
h323
!
voice class custom-cptone GB
dualtone conference
  frequency 600 900
!
!
!
!
license udi pid CISCO2951/K9 sn FCZ144620E4
hw-module pvdm 0/0
!
--More--                           hw-module sm 2
!
!
!
username admin privilege 15 secret 5 $1$RN9a$pHWWFc2aZ3SS3k6LR2SPX.
username Suman password 7 06444D
!
redundancy
!
!
controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-16
!
!
!
!
!
interface GigabitEthernet0/0
description $ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$$ETH-LAN$
no ip address
duplex auto
speed auto
--More--                           !
interface GigabitEthernet0/0.1
encapsulation dot1Q 1 native
ip address 10.83.100.250 255.255.255.0
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
!
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
duplex auto
speed auto
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
--More--                           interface Integrated-Service-Engine2/0
ip unnumbered GigabitEthernet0/0.1
service-module ip address 10.83.100.251 255.255.255.0
!Application: CUE Running on NME
service-module ip default-gateway 10.83.100.250
no keepalive
!
ip forward-protocol nd
!
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:/cme-gui-8.0.0.0.tar
!
ip route 0.0.0.0 0.0.0.0 10.83.100.254
ip route 10.83.100.251 255.255.255.255 Integrated-Service-Engine2/0
!
!
nls resp-timeout 1
cpd cr-id 1
!
!
--More--                           control-plane
!
!
voice-port 0/0/0:15
cptone GB
bearer-cap Speech
!
voice-port 0/1/0
cptone AE
description Fax
station-id name Fax
station-id number 400
caller-id enable
!
voice-port 0/1/1
!
voice-port 0/1/2
!
voice-port 0/1/3
!
!
!
sccp local GigabitEthernet0/0.1
--More--                           sccp ccm 10.83.100.250 identifier 1 version 4.0
sccp
!
sccp ccm group 2
associate ccm 1 priority 1
associate profile 2 register confprof2
!
sccp ccm group 1
!
dspfarm profile 2 conference 
codec g711ulaw
codec g711alaw
maximum sessions 5
associate application SCCP
!
dial-peer voice 10 pots
destination-pattern 0T
incoming called-number .
direct-inward-dial
port 0/0/0:15
!
dial-peer voice 101 pots
destination-pattern 4400400
--More--                            port 0/1/0
!
dial-peer voice 6000 voip
destination-pattern 6...
session protocol sipv2
session target ipv4:10.83.100.251
dtmf-relay sip-notify
codec g711ulaw
no vad
!
!
!
!
gatekeeper
shutdown
!
!
telephony-service
sdspfarm units 5
sdspfarm tag 1 confprof2
conference hardware
no auto-reg-ephone
authentication credential admin admin
--More--                            max-ephones 150
max-dn 500
ip source-address 10.83.100.250 port 2000
max-redirect 5
auto assign 10 to 150
system message Leighton Offshore Middle East
url services http://10.83.38.251/voiceview/common/login.do
url authentication http://10.83.38.250/CCMCIP/authenticate.asp 
load 7941 P00308000400
time-zone 35
date-format dd-mm-yy
dialplan-pattern 1 0444003.. extension-length 3 extension-pattern 3..
dialplan-pattern 2 0444004.. extension-length 3 extension-pattern 4..
voicemail 6000
max-conferences 8 gain -6
web admin system name admin secret 5 $1$I.S5$AuiJwPeKuOu.F0un7bGA2/
transfer-system full-consult
transfer-pattern 4..
transfer-pattern 3..
secondary-dialtone 0
--More--                            create cnf-files version-stamp 7960 Apr 07 2011 17:50:15
!
!
ephone-template  1
!
!
ephone-dn  1  dual-line
number 300 secondary 4400300
label Jannete Guarina - Receptionist
!
!
ephone-dn  2  octo-line
number 301 secondary 4400301
!
!
ephone-dn  3  dual-line
number 302 secondary 4400302
!
!
ephone-dn  4  dual-line
number 303 secondary 4400303
!
!
!
!
ephone-dn  112  octo-line
number A001
conference ad-hoc
preference 3
!
!
ephone-dn  113  octo-line
number A002
conference ad-hoc
preference 3
!
!
ephone-dn  114  octo-line
number A003
conference ad-hoc
preference 3
--More--                           !
!
ephone-dn  115  octo-line
number A004
conference ad-hoc
preference 3
!
!
ephone-dn  116  octo-line
number A005
conference ad-hoc
preference 3
!
!
!
!
ephone-dn  498
number 8000...
mwi on
!
!
ephone-dn  499
number 8001...
mwi off
!
!
ephone  1
mac-address 1C17.D341.FCB3
type 7962 addon 1 7915-12
button  1:1
!
--More--                           !
!
ephone  2
mac-address 0004.F2E8.FD8C
type 7937
button  1:2
!
!
!
ephone  3
mac-address 0004.F2E8.FE90
type 7937
button  1:3
!
!
!
ephone  4
mac-address 0004.F2E8.FD3C
type 7937
button  1:4
!
!
!
!
!
line con 0
login local
line aux 0
line 131
no activation-character
no exec
transport preferred none
transport input all
--More--                            transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
ntp master
ntp update-calendar
ntp server 10.83.100.250
end

Cyril,

It is not needed to see all the phone configuration with names and number. For security, I recommend you edit it out.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: