07-29-2011 09:30 PM - edited 03-16-2019 06:12 AM
Dear all,
I have a problem when siemen ip phone call to cisco ip phone, it not display caller name.
But cisco ip phone call to siemen ip phone is show caller name.
It can display caller name when I use CUCM version 6.1 but now I upgrade to CUCM 8.5 already.
My diagram
cisco ip phone (4605) <--> router (MGCP) <--> PBX (Siemen) <--> siemen ip phone
(5959)
I debug isdn q931 and show this result
Jul 29 12:34:09.825 TH: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x098F
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9FAA06800100820100A1180201000201008010507261736F6E672E4C75202D20494354
Calling Party Number i = 0x0081, '4605'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '5959'
Plan:Unknown, Type:Unknown
Jul 29 12:34:09.885 TH: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x898F
Channel ID i = 0xA98381
Exclusive, Channel 1
Jul 29 12:34:09.925 TH: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x898F
Facility i = 0x9FAA068001008201008B0100A1150202DCA506082B0C02885302010603050011000000
Facility i = 0x9FAA068001008201008B0100A10F0202DCB402015530068204061C0840
Facility i = 0x9FAA068001008201008B0100A1170202DCC3020101A10E040949342D4F4E53495445020101
Facility i = 0x9FAA068001008201018B0100A14A0202DCD206082B0C028853020100303A810C0C06008035393539740200C0822A031902000410000000600000040400C00E38008F048005000088836301C37C0A8349342D4F4E53495445
Progress Ind i = 0x8088 - In-band info or appropriate now available
Jul 29 12:34:11.233 TH: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x098F
Cause i = 0x8090 - Normal call clearing
Jul 29 12:34:11.341 TH: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x898F
Cause i = 0x8090 - Normal call clearing
Jul 29 12:34:11.349 TH: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x098F
How I configure any command at voice gateway or change at CUCM.
Please help.
Thank you
07-30-2011 07:05 AM
Hi
are these checked under the port which is connect to the siemen PBX ?
07-30-2011 10:46 AM
Hi Linuxchild,
I try already but still not display.
Please help
Thank you
07-30-2011 12:33 PM
Hello
I don't know if this has relation to your installation
but I have found this
Calling Line (Number) Identification Restriction (CLIR) is not supported by the Siemens PBX for outgoing calls. The PBX does honor CLIR on incoming calls, however.
http://www.ciscopaw.net/en/US/docs/voice_ip_comm/cucme/pbx/interop/notes/571119nt.pdf
07-30-2011 08:22 PM
Hi,
I have worked with CUCM <>H323 GW <> E1 ISDN <> Siemens PBX and CLID works fine in both direction. Could you post your debug output in the other way direction (Siemens calls Cisco).
Thanks!
07-31-2011 11:46 AM
Hi
Have you checked 'Send Calling Name in Facility IE' on the E1 config page?
Try that and reset.
Aaron
07-31-2011 06:21 PM
Hi
I configure MGCP this below
Then I cannot configure anything.
Thank you.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: